WMF 1300 S Скачать руководство пользователя страница 78

Страница: 78 / 136

User Manual WMF 1300 S

Software | System

Filter capacity (water filter)

If the water filter is active, the filter capacity in liters is
entered here.

Eco mode

The Eco mode can be activated here.
Options:

• active

• inactive

Default value:

inactive

Switch off

If Eco mode is active, the switch-off time can be set.

Options: (never / after 30 min/60 min/90 min/

120 min/ 150 min/180 min)

Standard: never

The time after the last beverage is dispensed is adjusted
here. If this time is exceeded, the coffee machine
automatically shuts off.
It can be set in increments of 30 minutes.
Eco mode can be activated for a limited time using
the timer.

Water filter capacity

page 29

DS_03_11_00_06

Eco mode

Eco mode

page 84

Содержание 1300 S









































































































































Результаты поиска

Содержание 1300 S

Отзывы:

Похожие инструкции для 1300 S

Бренды по названию

Популярные бренды

WMF 1300 S, Руководство пользователя

Результаты поиска

Содержание 1300 S

Отзывы:

Похожие инструкции для 1300 S

Бренды по названию

Популярные бренды