background image

W7500S2E-R1 serial to Ethernet module 

W7500S2E-R1 user manual 

Introduction 

W7500S2E-R1 is an industrial grade serial to Ethernet module. It supports TCP server, TCP client and UDP three 
operating  modes.  The  maximum  serial  baud  rate  is  460,800Mbps.  W7500S2E-R1  supports  WIZS2E  ConfigTool 
(Configuration Tool for Windows®), web page configuration and AT command to configure the module. 
W7500S2E-R1 uses W7500 MCU with hardwired TCP/IP protocol. This enable a faster, stable and secure Ethernet 
connectivity. With reference schematic(s) and guideline(s) in this user manual, it could be greatly reduced the time 
and difficulty of the hardware design and development when comparing with other approaches.

 

Features 

 

10/100 Mbps Ethernet interface with auto-negotiation and RJ45 connector 

 

Support TCP server, TCP client and UDP operating modes 

 

Flexible serial interface data packaging condition settings 

 

Smart Ethernet cable detection and keep alive features 

 

As DHCP client to automatically acquire IP address 

 

As DNS client to lookup domain name   

 

Support NetBIOS allows user to identify module’s name 

 

Support user password authorization for security 

 

Support serial AT command configuration method   

 

Built-in web server for browser and remote configuring 

 

Provide user-friendly configuration tool program (WIZS2E ConfigTool) 

 

Support firmware upgrade by ConfigTool

 

Specification

 

 

Serial interface: 3.3V TTL x1: TXD, RXD, GND 

 

Default Serial communication parameters 

o

 

Baud Rate: From 300bps to 460,800bps 

o

 

Data Bit: 7, 8 

o

 

Stop Bit: 1, 2 

o

 

Parity: None, Even, Odd 

o

 

Flow Control: None, CTS/RTS

 

 

Configuration methods 

o

 

WIZS2E ConfigTool 

o

 

Web based (via web browser) 

o

 

Serial AT command 

 

Power supply: Input Power: DC 3.3V 

 

Size: 44.45 x 31.75 x 23 (mm) 

 

Operating temperature: -40 ~ +85 ℃ (Industrial Grade) 

 

Storage environment: -40 ~ +85 ℃, 5 ~ 95% RH 

Version 

Date 

Remarks 

Содержание W7500S2E-R1
















































Отзывы: