Wiznet W7500 Скачать руководство пользователя страница 382

Страница: 382 / 399

W7500x Reference Manual Version1.1.0

382 / 399

SSP0 Control register 1 (SSP0CR1)

Address offset: 0x0004

Reset value: 0x0000_0000

res

SOD MS

SSE

LBM

R/W R/W R/W R/W

[0] LBM – Loop back mode:

0 : normal serial port operation enabled

1 : output of transmit serial shifter is connected to input of receive serial

shifter internally

[1] SSE – Synchronous serial port enable:

0 : SSP0 operation disabled.

1 : SSP0 operation enabled.

[2] MS – Master or Slave mode select:

0 : device configured as master, default.

1 : device configured as slave.

[3] SOD – Slave-mode output disable.

This bit is relevant only in the slave mode, MS = 1. In multiple-slave systems, it is

possible for a SSP0 master to broadcast a message to all slaves in the system while

ensuring that only one slave drives data onto its serial output line. In such systems the

RXD lines from multiple slaves could be tied together.

To operate in such systems, the SOD bit can be set if the SSP0 slave is not supposed to

drive the SSPTXD line:

0 : SSP0 can drive the SSPTXD output in slave mode.

1 : SSP0 must not drive the SSPTXD output in slave mode.

SSP0 Data register (SSP0DR)

Address offset: 0x0008

Reset value: 0x0000_0000

res

Содержание W7500















































































































































































































































































































































































































Результаты поиска

Содержание W7500

Отзывы:

Похожие инструкции для W7500

Бренды по названию

Популярные бренды

Wiznet W7500, Справочное руководство

Результаты поиска

Содержание W7500

Отзывы:

Похожие инструкции для W7500

Бренды по названию

Популярные бренды