24
www
.wittur
.com
Changes can be made without notice
PM.2.004923.EN - 811-000-000 SDS
©
DC-PWM Compatible · Edition 22 July 2020
Drive - Instruction Manual
7.3 REVERSING SYSTEM FORCE SETTING BY MEANS OF THE HANDSET
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the MAIN MENU and choose PROFILE SETTINGS;
•
Press the “OK” key to confirm the option.
•
On the display the following options are viewed:
−
FAST SETTING
−
REVERSING SYSTEM
−
ADVANCED SETTINGS
−
RESERVED AREA
•
Using keys
ã
and
ä
run through the menu “PROFILE SETTING” and choose the option REVERSING SYSTEM FORCE
•
Using the “OK” key, confirm the option
On the left display side three values are shown selectable with
ã
and
ä
keys: the maximum value (MAX), the set value (SET) and the
minimum value (MIN).
It is possible to change those values with
á
and
â
.
On the right display side a graph is shown with the set force percentage regarding the maximum force.
•
Using keys
á
and
â
the viewed value is respectively decreased or increased;
•
Press key F2 (<> - ><) to check the door operation with the set reversing force value
•
Press key F3 (Menu) to restore the MAIN MENU
•
Press key F1 (BACK) to restore the menu PROFILE SETTINGS;
7.4 SPEED PROFILE AND HIGH SPEED ADJUSTMENTS BY MEANS OF THE HANDSET
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the “MAIN MENU” and choose “PROFILE SETTINGS”;
•
Press the “OK” key to confirm the option
•
On the display the following options are viewed:
−
FAST SETTING
−
REVERSING SYSTEM
−
ADVANCED SETTINGS
−
RESERVED AREA
•
Using keys
ã
and
ä
run through the menu “PROFILE SETTINGS” and choose the required option
•
Using the “OK” key, confirm the option
•
The following options are available:
−
“BACK”: press key F1 to restore the “MAIN MENU”;
−
“MENU”: press key F3 to restore the “MAIN MENU”;
7.4.1 Option “Fast settings”
This option allows to easily and quickly modify the speed profiles. Choose this option as indicated in the first part of
reversal Activation by means of the handset” a pag. 27
The following options are viewed on the display:
•
OPENING PARAMETERS;
•
A diagram shows the examined cycle speed profile (opening or closing);
•
On the upper left side a number is given which indicates the currently used speed percentage. Using keys
ã
and
ä
on the handset
to modify it.
•
On the lower left side a number is given which indicates the currently used speed m/s.
•
On the lower left side a number is given which indicates the time “T:” in seconds required to perform the opening cycle;
•
Using keys
ã
and
ä
, the value of the speed parameter is respectively increased or decreased;
•
Using keys
á
and
â
, it is possible to change the parameter to be set; the parameters which are available are “HIGH SPEED”, “LOW
SPEED”, “COMFORT”;
•
The parameter “Comfort” determines acceleration value or deceleration value that the controller has to comply with while
changing profile velocity. This parameter is important to establish the panel fluidness movement. The display shows the parameter
value expressed in percentage and below the real value of the parameter;
•
At the end of the parameters modifications the diagram will adapt and will show the new speed profile;
•
Press key F2 (<> - ><) to check the door operation with the new set profile and, by performing an opening cycle, this will update the
indicator of time necessary to carry out the opening cycle with the new set profile;
•
Press key F3 (NEXT) to carry on the profile setting with the CLOSING PARAMETERS setting; the same operations must be followed
as above in relation to the OPENING PARAMETERS setting;
•
Press key F1 (BACK) to the previous menu;
7.5 OPTION “ADVANCED SETTINGS”
•
Connect the handset to RJ45 connector
•
If necessary, using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the MAIN MENU and choose PROFILE SETTING;
•
Press the “OK” key to confirm the option
•
On the display the following options are viewed:
−
FAST SETTING
−
REVERSING SYSTEM
−
ADVANCED SETTINGS
