background image

 

 

Home Lift - Elevating platform 

 

Test instructions 

 

 Subject to change without notice!

 

EXCELLENCE IN COMPONENTS

 

Date 

 

07/10/2011 

Sheet 

 

Version 

 

11117320015V02 

Approved   

ISC

 

 

Original instructions 

 

1

 

Purpose  and  scope  of 
application 

of 

these 

instructions. 

 
The  purpose  of  these  instructions  is  to 
determine  procedures  to  do  the  final 
examinations and tests according the standard 
EN81-41,  so  as  to  the  putting  into  service  of 
the lifting platform once the final control and 
tests are done.  
 
 

2

 

Designations and Terms 

 
The definitions used in these instructions are as 
follows:  
 
 

Lifting platform equipment terms 
 
Suspension 2:1 

A  traction-lifting  platform  whose  car  and/or 
counterweight are connected with rope pulleys 
and traction sheaves. 
 

Unlocking zone 

The zone above and below the stop where the 
car floor has to be in order to unlock the shaft 
door at this stop. 
 

Levelling 

A process that improves the stopping accuracy 
at floor levels. 
 

Safety Gear 

A  mechanical  component  for  braking  and 
holding  the  car  if  it  is  travelling  with  over 
speed or if the suspension ropes break. 
 

Pit 

The part of the well below the lowest stop that 
the car stops at. 

 
Drive 

Equipment  that  moves  and  stops  the  lifting 
platform. 

 

3

 

Safety advice 

 

It is essential to comply with all applicable national 
safety  regulations  and  legal  provisions  to  prevent 
personal injury in assembly, service and repair work 
on the product. 

 
The symbols below draw particular attention to 
instructions  of  special  importance  for  safety 
and injury prevention: 
 

general hazard sign 
 
 
 
symbol  for  augmented  danger  of 
injury  (for  instance,  from  edges 
where hands could get crushed) 
 
 
symbol  for  potential  component 
damage  (for  instance,  due  to 
defective assembly) 
 
symbol for important information 
 

 
Thoughtless  behaviours  or  non-compliance 
with  rules  or  safety  advice  can  cause  the 
following types of accidents: 
 
- shearing 
- crushing 
- falling 
- impact 
- trapping 
- fire 
- electric shock 
- damage to components 
- the consequences of wear and tear 
- the consequences of corrosion 

3.1

 

Safety advice for the operator 

 

The operator is called upon to urge 
proper  use  of  the  lifting  platform 
and  warn  users  about  hazards.  The 

Содержание HHL-W Line















Отзывы: