Wisenet TNF-9010 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

background image

10_

installation & connection

installation & connection

INSTALLATION

Precautions before installation

Ensure you read out the following instructions before installing the camera:

~

Select an installation site that can hold at least 5 times the camera’s weight.

~

Stuck-in or peeled-off cables can cause damage to the product or a fire.

~

For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.

~

If the product is installed with excessive force, it may cause damage to the camera due to malfunction.
Forcing assembly using non-compliant tools may damage the product.

Disassembling

1.

Peel off the tape that holds the mount plate and camera body, and detach the mount plate.

2.

Turn the top cover in the direction of the arrow to remove it.

3.

Peel off the camera lens protective film.

«
...
8
9
10
11
12
...
»

Содержание TNF-9010





























Отзывы:

Нет отзывов

Похожие инструкции для TNF-9010

Бренд: CAME Страницы: 80

Бренд: FALEEMI Страницы: 14

Multi Gas Clip Simple Plus

Бренд: Gas Clip Technologies Страницы: 20

Бренд: CAME Страницы: 2

ED 14-42mm f3.5-5.66 EZ

Бренд: Olympus Страницы: 15

Бренд: Digital Watchdog Страницы: 2

Бренд: Vivotek Страницы: 2

Бренд: Vicon Страницы: 28

RoboSHOT 12E HDBT

Бренд: VADDIO Страницы: 2

Бренд: Stealth Cam Страницы: 45

Бренд: Dahua Страницы: 29

Бренд: HACA LEITERN Страницы: 64

Vantage Pro2 GroWeather 6820

Бренд: DAVIS Страницы: 36

Бренд: YI Страницы: 22

GlassTrek DG457

Бренд: Paradox Страницы: 2

Mainline CV-M13B10-ODI

Бренд: Clare Controls Страницы: 36

Бренд: Leica Страницы: 358

Бренд: Novus Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды