Wisenet TNF-9010 Скачать руководство пользователя страница 17

Страница: 17 / 28

English _

INST

ALLA

TION & CONNECTION

Connecting to Audio Input/Output

Speaker

Microphone

Network

Connect the MIC port of the camera with the microphone or LINE OUT port of the amplifier that the
microphone is connected to.

Connect the SPEAKER port of the camera with the speaker or LINE IN port of the amplifier that the
speaker is connected to.

Check the specifications for audio input.

Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate:

16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling
Frequency: 16kHz)

Full duplex Audio

Audio in

: Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm

Audio out

: Line-out (3.5mm mono jack), Maximum output: 1Vms, Line out impedance : 600Ω

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

Alarm

(Warning lamp)

Sensor

ALARM #1, ALARM #2 : These ports can be used as alarm input or output ports. If used as input ports,

alarm input or day/night sensors can be connect to them. If used as output ports,
alarm output signals can be connect to them.

※

Alarm I/O changes can be made through the Webviewer setup.

GND : Common port for alarm in/output signal.

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open
collector method, it may cause malfunction.
Refer to the “

Alarm Out Wiring Diagram

” when connecting devices that exceed the voltage and current specifications.

(Page 18)

Содержание TNF-9010





























Результаты поиска

Содержание TNF-9010

Отзывы:

Похожие инструкции для TNF-9010

Бренды по названию

Популярные бренды

Wisenet TNF-9010, Руководство пользователя

Результаты поиска

Содержание TNF-9010

Отзывы:

Похожие инструкции для TNF-9010

Бренды по названию

Популярные бренды