Wisenet PNM-9322VQP Скачать руководство пользователя страница 16

Страница: 16 / 28

installation & connection

16_

installation & connection

Adjusting the monitoring direction for the camera

Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling.
The act of moving the camera module is called “Pan”; adjusting its angle “Tilt”; rotating the lens along the
axis “Rotate”.

- The rotation angle of Pan is -90˚ to +90˚ for each module.

- The rotation angle of Rotation is -180˚ to +180˚.

- The rotation angle of Tilt varies for each lens. See the table below.

The image can be covered up by the camera case depending on the angle.

Do not pan over the specified rotation angle. It might damage the cable leading to a product malfunction.

Methods of adjustment

After installing the camera in consideration of the direction to monitor, adjust the Pan angle along the
bottom rail.

Adjust the horizontal angle so that the image does not appear to be reversed during rotation.

Adjust the tilt angle so that it points in the direction to be monitored.

Tilting angle range for each lens module

Lens module

name

SLA-

2M2400P

SLA-

2M2800P

SLA-

2M3600P

SLA-

2M6000P

SLA-

2M1200P

SLA-

5M3700P

SLA-

5M4600P

SLA-

5M7000P

Normal

installation

52˚~56˚

26˚~80˚

22˚~84˚

10˚~95˚

10˚~97˚

36˚~73˚

21˚~85˚

12˚~93˚

For

HallywayView

Not

supported

37˚~70˚

33˚~73˚

17˚~88˚

12˚~92˚

45˚~62˚

38˚~74˚

21˚~85˚

A partial blockage of view at a corner of the monitor may occur as the result of installation beyond the allowed angle
range.

CONNECTING WITH OTHER DEVICE

Camera Wiring Interface Board

For the camera wiring, please refer to the picture below.

When the alarm output is connected as Normal Open:

the sensor input operates when it is short for point contact type, or at the “LOW” level for active type.

The maximum capacity of the alarm output terminal is 30V DC/2A, 125V AC/0.5A and 250V AC/0.25A.

When connecting alarm input and output cables, be sure to connect one cable to each terminal respectively.

To connect products over the camera’s capacity, please use an additional relay device.

Improper connection of GND with NC/NO port and COM port might cause fire or product damage.

Moving the camera module (Pan)

Tilt

HPoE

Alarm

Alarm Input

Alarm output

Audio input/

output

Содержание PNM-9322VQP





























Результаты поиска

Содержание PNM-9322VQP

Отзывы:

Похожие инструкции для PNM-9322VQP

Бренды по названию

Популярные бренды

Wisenet PNM-9322VQP, Руководство пользователя

Результаты поиска

Содержание PNM-9322VQP

Отзывы:

Похожие инструкции для PNM-9322VQP

Бренды по названию

Популярные бренды