Wisenet LRN-810S, Руководство пользователя

Страница: 51 / 123

English
_51
Record Setup
You can set the resolution and number of recordings for each channel when an event occurs or during a normal
recording.
You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel,
and set the transfer limit for recordings.
Setup > Record > Record setup
●
Apply to other channels : If you select <
Apply to other channels
>, “
Apply to other channels
” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on <
OK
> to apply them to the selected
channels.
●
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Continuous recording / Event recording : Set the recording method for Continuous recording or Event
recording.
– Full frame : Records all frames fed by the camera.
– I-frame : Records only key frames fed by the camera. It depends on the camera's settings.
– Off : No recording is made.
●
Frame
– Full frame : Shows the amount of data for all the scene recordings.
– I-frame : Shows the amount of data for the main scene recordings.
●
Limit : Set the amount of data allowed for input for each channel.
●
Event : When an event occurs, you can set which point you will start or stop recording.
– Pre : When an event occurs, recording will be started regardless of the time set.
If you set it to five seconds, recording will start at five seconds before an event occurs.
– Post : When an event occurs, recording will continue after the time set.
If you set it to five seconds, recording will continue for a further five seconds after an event is finished.
●
Audio : Specify whether to record the sound received from the camera or not.
￭
If a channel's data transfer exceeds defined allowed limit, then it may affect to other channels, and may force switching to < I-frame >
recording even when the channel is configured to < Full frame > recording mode. For Key Frame recording channels, the icon for limited
recording appears on the live screen's top side.
But if the sum of the limits is below the max limit, you can still receive the entire frames despite exceeding the permitted bitrates for each
channel.
￭
A channel displayed in yellow indicates that the recorded data is not being transferred from the camera and that the recording is being
performed temporarily using another profile on the camera.
Check the channel information to see the applied profile to the channel listed in yellow.
A channel displayed in orange indicates that the amount of inputted data is greater than the permitted data amount. In this case, it is
impossible to record all of the incoming frames. Instead, only part of the frames (1 or 2 frames per second) can be recorded.
To resolve this issue, you must set the permitted data amount to be greater than the amount of inputted data.
Refer to the "
Live > Live screen mode > Check the camera status " page in the Table of Contents.
Record Options
You can set recording options, such as enabling dual recording or overwrite of hard disk for repeated recording.
Setup > Record > Record options
●
Enable dual recording : Select this if you want to record both the recording profile and remote profile at the
same time. Enabling dual recording is applied with a profile suitable for split mode during playback.
●
Overwrite : Select the recording method when the hard disk storage capacity is full.
– Checked ( ) : If the HDD is full, this will overwrite the existing data and keep recording.
– Not checked ( ) : If the HDD is full, this will stop recording automatically.
●
Beeps when recording is stopped: If <
Overwrite
> has not been set, this button is enabled. Specifies whether
to use beep or not when HDD recording ends.
If you check it, the beep will sound on the disk full and the recording stops.
●
Retention period : If you check this option, the period list box is active, and you can set the automatic deletion
period. Specify the deletion period to delete any earlier data than the specified date. However, you can search
for data from the current time to the selected date.
￭
If < Overwrite > has been set, this button is enabled.
￭
You can select a channel and set a different recording duration for each channel.
●
Apply to other channels : If you select <
Apply to other channels
>, “
Apply to other channels
” confirmation
window will appear. After selecting channels that the settings will be applied to, click on <
OK
> to apply them
to the selected channels.
￭
If you press < Retention period > when you have completed your settings, all the existing data earlier than the specified period will be
deleted automatically. If you need to keep your old data, export it first.
•
SE
Tu
P