background image

4_ safety information

Safety information

6.  Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled 

with water on top of the camera. doing so may cause personal injury due to fire, electric shock, 
or falling objects.

7.  Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric 

shock.

8.  If any unusual smells or smoke come from the unit, stop using the product. in such case, 

immediately disconnect the power source and contact the service center. continued use in 
such a condition may cause fire or electric shock.

9.  If this product fails to operate normally, contact the nearest service center. never disassemble 

or modify this product in any way. (Hanwha Techwin is not liable for problems caused by 
unauthorized modifications or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product. doing so may cause fire 

or electric shock.

CAUTION

1.  Do not drop objects on the product or apply strong shock to it. Keep away from a location 

subject to excessive vibrationor magnetic interference.

2.  Do not install in a location subject to high temperature (over 55 °C), low temperature  

(below -30 °C), or high humidity. Doing so may cause fire or electric shock.

3.  If you want to relocate the already installed product, be sure to turn off the power and then 

move or reinstall it.

4.  Remove the power plug from the outlet when then there is a lightning. Neglecting to do so 

may cause fire or damage to the product.

5.  Keep out of direct sunlight and heat radiation sources. It may cause fire.

6.  Install it in a place with good ventilation.

7.  Avoid aiming the camera directly towards extremely bright objects such as sun, as this may 

damage the CMOS image sensor.

8.  Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, 

such as vases, shall be placed on the apparatus.

9.  The Mains plug is used as a disconnect device and shall stay readily operable at any time

10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.

Содержание HCF-8010V





























Отзывы: