Wisenet CT-XNO-6123R Скачать руководство пользователя страница 27

Страница: 27 / 39

English _

INST

ALLA

TION & CONNECTION

Connecting to Audio Input/Output

Network

Microphone

Speaker

Microphone

Speaker

Connect the MIC port of the camera with the microphone or LINE OUT port of the amplifier that the
microphone is connected to.

Connect the SPEAKER port of the camera with the speaker or LINE IN port of the amplifier that the
speaker is connected to.

Check the specifications for audio input.

Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate:

16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling
Frequency: 16kHz)

- Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)

Full duplex Audio

Audio in

: Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm

Audio out

: Line-out (3.5mm mono jack), Maximum output: 1Vms, Line out impedance

: 600Ω

In the case you access the web viewer and select an external microphone as the audio input sources in <

Video & Audio

> -

Audio setup

>, the following specifications are recommended:

Frequency range: 40-16,000 Hz

Impedance: 1,500 Ω

Sensitivity: -40±3 dB (7.1-14.1 mV)

In any of the following cases, sound classification performance may be degraded or malfunction:

If gunshot sounds are heard continuously in a short interval (e.g. machine gun sound) rather than a one-time gunshot
sound

If the noise is too loud for the noise and the target sound to be distinguished

If two or more of different sounds are registered simultaneously

If the sound classification is applied while using the noise removal function in a quiet place

If the source of clapping sounds or screams is close to the camera (within 1 meter)

If a sound that does not belong to any of the sound classification categories (airplanes sound, siren sound, etc.) is loudly
heard all of sudden

If external microphone does not meet the recommended specifications

Содержание CT-XNO-6123R








































Результаты поиска

Содержание CT-XNO-6123R

Отзывы:

Похожие инструкции для CT-XNO-6123R

Бренды по названию

Популярные бренды

Wisenet CT-XNO-6123R, Руководство пользователя

Результаты поиска

Содержание CT-XNO-6123R

Отзывы:

Похожие инструкции для CT-XNO-6123R

Бренды по названию

Популярные бренды