background image

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other 

household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains 

mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these 

substances can cause harm to human health or the environment. 

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them 

through your local, free battery return system.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. 

charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. 

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate 

these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material 

resources.

Household users should contact either the retailer where they purchased this product, or their local government 

office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This 

product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide 

customers with more environmentally friendly products. 

The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates 

that the product satisfies the EU RoHS Directive. 

Any changes or modifications in construction of this device which are not expressly approved by the 

party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference when the equipment is operated in a commercial environment. 

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used 

in accordance with the instruction manual, may cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful interference in which case 

the user will be required to correct the interference at his own expense.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the  

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Содержание 2M2800Q




























Отзывы: