background image

Copyright 

©2020 

Hanwha Techwin

 Co., Ltd. All rights reserved.

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their 
respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without 
formal authorization. 

Disclaimer

Hanwha Techwin

 makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be 

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. 

Hanwha Techwin

 reserves the 

right to change the contents of this document without prior notice.

 

™

Design and specifications are subject to change without prior notice.

 

™

The initial administrator ID is “admin” and the password should be set when logging in for the first time. 
Please change your password every three months to safely protect personal information and to prevent the damage of the information 
theft. 
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

Network Camera

User Manual

Содержание 2M2800Q




























Отзывы: