Wirepath Surveillance WPS-550-DOM-IP страница 11 Скачать руководство пользователя

Страница: 11 / 63

WPS-550-DOM-IP Installation Manual

7. Camera Installation Instructions

7.1. Wiring Installation

A. Run a Cat5e/6 cable from the network port to the camera location and terminate both ends to 568B.
B. (Non-PoE applications only) Run wiring to the camera from the power supply location. Use the voltage drop calculator at

www.

SnapAV.com

to determine the wire size needed.

C. (Non-PoE applications only) Connect the power supply to the wire at the head end using electrical connectors (not included),

and attach the WPS-ACC-PWR-M to the wire at the camera location. Be sure to use the correct polarity.

D. (Non-PoE applications only) Connect the power supply to a suitable outlet and test the voltage at the camera side of the wire

using a volt meter. Disconnect the power supply from the outlet until camera installation is otherwise complete.

7.2. Camera Mounting

Important Note:

To avoid damaging the dome surface during installation, keep the dome surface away from walls and other

objects. Do not remove the protective film from the dome until after the camera is mounted and the dome installed.

A. Unpack the camera and open the dome. Do not remove the protective film from

the dome.

B. If the camera is going to be surface mounted, use the provided foam gasket as

a template to mark 3 mounting hole locations, and then make pilot holes for the

screws. If a mounting accessory is being used, install the accessory over the

wiring according to the included instructions.

C. Attach the foam gasket to the bottom of the camera base. Pull the cable through

the side of the housing knockout if needed.

D. Connect the wiring to the camera, then push the wiring into the box or cavity

behind the camera.

E. Secure the camera to the accessory or surface using 3 screws.

F. Install a microSD card in the slot if desired.

croSD Card S

G. Pull the test adapter from inside the dome housing if needed for attaching a test

monitor and power supply.

Содержание WPS-550-DOM-IP
































































Результаты поиска

Содержание WPS-550-DOM-IP

Отзывы:

Похожие инструкции для WPS-550-DOM-IP

Бренды по названию

Популярные бренды

Wirepath Surveillance WPS-550-DOM-IP, Руководство пользователя

Результаты поиска

Содержание WPS-550-DOM-IP

Отзывы:

Похожие инструкции для WPS-550-DOM-IP

Бренды по названию

Популярные бренды