Wireless ACW/LW8-DIND160 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 41

Wireless ACW/LW8-DIND160 Скачать руководство пользователя страница 5

4

ACW-DINDxxx_UG_EN_V1.8

Declaration of compliance

All ACW Atim Cloud Wireless® products comply with the regulatory requirements of the R&TTE Directive
(1999/5/EC), article 3:

1 SAFETY (Article 3.1a of the 1999/5/EC Directive)
NF EN60950-1 Ed. 2006/A1:2010/A11:2009/A12:2011 (health)
EN62479: 2010 (power <20mW) or EN62311:2008 (power > 20mW)

2 Electromagnetic compatibility (Article 3.1b of the 1999/5/EC Directive)
EN 301489-3 v1.4.1, EN 301489-1 V1.9.2

3 Efficient use of the radio frequency spectrum (Art.3.2 of the 1999/5/EC

Directive)

ETSI EN300 220-2 v2.4.1 and EN300 220-1 v2.4.1

Environmental recommendations

a.

Explosive atmosphere

Except for the ACW-ATEX line specifically intended for this purpose, do not use ACW radio modems in
the presence of flammable gases or fumes. Using the equipment in such an environment constitutes a
safety hazard.

b.

Environment

Respect the temperature ranges for storage and operation of all products. Failing to respect these
guidelines could disrupt device operation or damage the equipment. ACW products in IP65 water- and
dust-resistant housings may be placed outdoors, but must not, under any circumstances, be submerged.

Follow the instructions and warnings provided below to ensure your own safety and that of the
environment and to protect your device from any potential damage.

«
...
3
4
5
6
7
...
»

Содержание ACW/LW8-DIND160










































Отзывы:

Нет отзывов