Wireless ACW/LW8-DIND160 страница 39 Скачать руководство пользователя

Страница: 39 / 41

ACW-DINDxxx_UG_EN_V1.8

Each program is represented in byte 2 as follows:

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Next day
off only

Program

state

Program

state

Program

state

Program

state

Program

state

Program

state

Program

state

If the state bit of a program is at "1," the program will be activated, if the state bit is at "0," the program
will be disabled.

In addition, by forcing bit 7 to "1," all activated programs will be inactive the next day and will become
active again the following day.

For example, if the 0x410B83 command is sent on a Tuesday, programs 1 and 2 will only be activated
from Thursday (programs 3,4,5.6 and 7 will be deactivated on right after the command).

Get output calendar state (0x0C)

The following command allows to get the output calendar state at any time:

Following this command, the ACW will return a response in the following format:

Description and value

Byte 0

Response to command frames: 0x07

Byte 1

“State of output calendars” command

: 0x0C

Byte 2

Output calendar states

The byte 2 in the response frame has the same format as byte 2 In the command frame.

Byte 0

Byte 1

0x01

0x0C

Содержание ACW/LW8-DIND160










































Результаты поиска

Содержание ACW/LW8-DIND160

Отзывы:

Похожие инструкции для ACW/LW8-DIND160

Бренды по названию

Популярные бренды

Wireless ACW/LW8-DIND160, Руководство пользователя

Результаты поиска

Содержание ACW/LW8-DIND160

Отзывы:

Похожие инструкции для ACW/LW8-DIND160

Бренды по названию

Популярные бренды