Wireless ACW/LW8-DIND160 страница 33 Скачать руководство пользователя

Страница: 33 / 41

ACW-DINDxxx_UG_EN_V1.8

Shock alarm configuration (code 41)

Byte 1 possible values are :

•

0x00 => shock alarm radio frame disabled

•

0x01 => shock alarm radio frame enabled

Commands

Restart (Command 0x01)

To restart the ACW-DINDIO8 / 16 remotely, you will need to send the following command:

Byte 0

Byte 1

0x01

The ACW will restart and not send confirmation.

About (Command 0x02)

To obtain the information about the ACW-DINDIO8 / 16 it will be necessary to send him the following
command:

Byte 0

Byte 1

0x01

0x02

The ACW will return the information in the following format:

Description and Value

Byte 0

Answer to command frames: 0x07

Byte 1

About command: 0x02

Byte 2

Type de l’ACW :

⚫

DIN D160 - 9

⚫

DIN D80 - 11

⚫

DIN D88 - 15

⚫

DIN D44 - 14

Byte 3

ACW version (LSB)

Byte 4

ACW version (MSB)

Byte 5

Radio type:
1.

Sigfox only uplink - 0x03

Sigfox uplink/downlink - 0x04

LoRaWan - 0x05

Byte 6

Radio version (LSB)

Byte 7

Radio version (MSB)

Byte 8 to n

Serial number (devEUI|sfx) (MSB first).

Reconfiguration with default settings (Command 0x03)

To reconfigure the parameters to the default values, it will be necessary to send him the following
command:

Size and Code (Byte 0)

Value (byte 1)

0x00|0x29 = 0x29

0xYY

Содержание ACW/LW8-DIND160










































Результаты поиска

Содержание ACW/LW8-DIND160

Отзывы:

Похожие инструкции для ACW/LW8-DIND160

Бренды по названию

Популярные бренды

Wireless ACW/LW8-DIND160, Руководство пользователя

Результаты поиска

Содержание ACW/LW8-DIND160

Отзывы:

Похожие инструкции для ACW/LW8-DIND160

Бренды по названию

Популярные бренды