Wipaire Wipline 2100 Скачать руководство пользователя страница 19

Страница: 19 / 70

SERVICE MANUAL & ICA

WIPLINE 2100 & 2350 FLOATS

P/N 1002549

Revision N

Page 19

Aft Cradle

Stand

Fore Cradle

Stand

Cradle

Fore

Support

Aft

Support

(8000A MODEL SHOWN FOR REFERENCE ONLY)

FIGURE 4-4 FLOAT SECURING LOCATIONS OVERVIEW

4.4 JACK REMOVAL

Make sure nothing is under or above the airplane or floats when removing the jacks from the aircraft

Turn off fuel.

Verify landing gear is in the down and locked position.

Verify weighted bags are still located above the nose gear.

Position 1 person at each fore and aft of each float, and 1 person at the jacking location of one float.

5. Remove all fore and aft supports as shown in Figure 4-3 and Figure 4-4.
6.

Using modified jack saddle as shown in Figure 4-1, center jack saddle in center of cradle on 1 of the floats,

Lift aircraft to clear fore and aft cradle stands and remove fore and aft cradle stands of lifted float.

Slowly lower float to the ground, remove jack from under float, and remove cradle from jack saddle.

Repeat previous procedure to the other float.

10.

Remove weighted bags from floats.

Содержание Wipline 2100







































































Результаты поиска

Содержание Wipline 2100

Отзывы:

Бренды по названию

Популярные бренды

Wipaire Wipline 2100, Руководство по обслуживанию и инструкции

Результаты поиска

Содержание Wipline 2100

Отзывы:

Бренды по названию

Популярные бренды