SmartPAC 2 with WPC 2000 Integration User Manual
1128600
Run Mode
6-49
Operating the Press in Automatic Single-stroke Mode
The Automatic Single-stroke function allows an external event to automatically initiate a
single stroke within a 30-second or 5-minute window, depending on the setting of option
switch 5 on the Press Control Option Switch Menu (see step 1, below). Generally, material
feed is used as the signaling event. However, other events such as part ejection or positive
part transfer can be used.
There are three requirements for Automatic Single-stroke:
•
Automatic Single-stroke must be enabled in Initialization (see page 4-41)
•
There must be a trigger mechanism.
•
Proper guarding equipment, such as a Shadow light curtain and fixed guards, must be
installed to protect personnel.
As a triggering mechanism, you can use a single-pole, double-throw (SPDT) contact (switch
or relay) or two solid-state switches (NPN, open collector). See Figure 3 at the end of the
manual.
If you intend to use Automatic Single-stroke, contact Wintriss Tech. Support.
To run the press in Automatic Single-stroke, first install the sensors and other components
required for this function, then do the following:
1.
Set option switch 5 on the Press Control Option Switch Menu to OPEN to select 30
seconds as the prior act timing or to CLOSED to select 5 minutes (see
Time for Automatic Stroke Modes
2.
Select “AUTOMATIC” on the Mode Select Menu (see page 6-40)
3.
Set the Stroke Select key switch to “SINGLE STROKE.”
IMPROPER SAFEGUARDING
Ensure that the machine guarding system is installed and maintained according to OSHA
regulation 1910.217, ANSI standards B11.1 and B11.19, and any other regulations or standards
that apply. Ensure that guarding is properly installed to prevent access to the machine over, under
or around any guarding device.
Failure to comply with these instructions will result in death or serious injury.
PRESS STARTING UNEXPECTEDLY
Ensure that light curtains and other safeguards are properly installed and operating to protect
operators when using Automatic Single-stroke. Since an external trigger initiates press operation,
a stroke can occur unexpectedly.
Failure to comply with these instructions will result in death or serious injury.
DANGER
!
DANGER
!
Содержание SmartPAC 2
