SmartPAC 2 with WPC 2000 Integration User Manual
1128600
Run Mode
6-31
The maximum and minimum speed limit settings are used to monitor press speed for tools run
on a variable-speed press. They apply to all Run operating modes–Continuous, Single-stroke,
and Inch. When the speed of the press exceeds the maximum limit, SmartPAC 2 stops the
press and displays the fault message “Maximum press speed exceeded.” When press speed
drops below the minimum limit, SmartPAC 2 stops the press and displays the fault message
“Minimum press speed exceeded.” These fault message are documented in Chapter 7 (see
page 7-30).
The counterbalance setpoint is used together with the counterbalance tolerance you set in
Initialization (see
Setting Clutch and Counterbalance Air Pressure Limits
specify the pressure range outside of which an F46 (Counterbalance Air Outside Sensor
Limits) error displays on the SmartPAC 2 LCD. This field does not display if the
Initialization tolerance value is set to zero (0), disabling the Counterbalance Setpoint feature.
To adjust one or more of these settings, do the following:
1.
Select PRESS CONTROL on the Main Run Menu. The Press Control Parameters screen
displays.
2.
Move the highlight bar to the desired item, and press ENTER. The Numeric Entry
window (see Figure 5-3, page 5-3) displays.
Figure 6-24. Press Control Parameters Screen
ARE YOU LOCKED OUT?
Access to items on this screen may be limited to Program mode or may require a
password. The security access settings in Initialization mode determine when changes
can be made. See Table 4-15, page 4-48.
F1
F2
F3
F4
F5
F6
F7
F8
NOTICE
Содержание SmartPAC 2
