Winter MULTIMAX 300 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 74

background image

MUL

TIMAX 300

Chapter 3: OPERATION

27

3-10 SAFETY DEVICE FOR SAW ARBOR

This machine has equipped with a safety device which allows the Saw Arbor Cover
be opened only when the saw arbor stops completely. When the Saw Arbor starts, it
starts the LOCK switch at the same time, and the Saw Arbor Cover can not be opened
as well. This can prevent the operator from the danger that results from the running
saw arbor while opening the cover

How to operate:

1.

Push the Emergency Stop Switch or Saw Blade Stop Button during saw arbor
running. At this moment, the sensor will detect the saw arbor running. After the
saw arbor stops completely, the indicator lamp will be on.

2.

When the indicator lamp is on, it means the saw arbor stops completely. Be sure
to press the indicator button and the other hand to open the door at the same time
until the pin takes off the lock. (Then, the operator can open the door completely
without pressing the indicator button).

«
...
31
32
33
34
35
...
»

Содержание MULTIMAX 300











































































Отзывы:

Нет отзывов

Похожие инструкции для MULTIMAX 300

Бренд: Parkside Страницы: 60

Бренд: Parkside Страницы: 132

Бренд: TOPMAQ Страницы: 15

Бренд: Euromate Страницы: 100

Бренд: King Canada Страницы: 12

Бренд: Pearl Страницы: 20

Бренд: EINHELL Страницы: 92

Бренд: Grizzly Страницы: 60

Norton Clipper CWT 255

Бренд: SAINT-GOBAIN Страницы: 28

Бренд: Scheppach Страницы: 111

Бренд: Scheppach Страницы: 152

Бренд: STALEX Страницы: 15

Бренд: Target Страницы: 14

Бренд: Power Glide Страницы: 8

Бренд: ALDI Страницы: 44

Бренд: Mafell Страницы: 94

Бренд: Westfalia Страницы: 42

Бренд: Milwaukee Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды