WinSystems EBC-C413 Скачать руководство пользователя страница 51

Страница: 51 / 83

EBC-C413/Configuration

v1.2

www.winsystems.com

Page 51

Additional Information

This connection is a 3M N7G24-A0B2EB-10-3WF (or equivalent).

7.12.27 204-pin SODIMM Socket for System Memory

The EBC-C413 supports up to eight GB DDR3L SODIMM system memory

through this one on-board socket.

7.13 Jumpers

Jumper PN SAMTEC 2SN-BK-G applies to all jumpers. These are available in

a ten piece kit from WINSYSTEMS (PN KIT-JMP-G-200).

7.13.1 JP104P - PCI-104 Power Source Select

Purpose:

Configures power source for the PC104-Plus (see “PC104P -

PC104-Plus/PC104 Bus Connector” on page 36).

7.13.2 JP5VSB - 5V Standby Power Select

Purpose:

Shorts 5 V and 5V_SB. Connect pins 1-2 when using AT power

supply; connect pins 2-3 or Open when using ATX power supply.

7.13.3 JPDIO1 - Power Enable (+5 VDC) to Pin 49 of DIO1

Purpose:

When present, this jumper connect Pins 1-2 and applies power

(+5 VDC, VCC1) to pin 49 of DIO1. With jumper removed, no voltage is

applied to Pin 49.

Jumper

PC104-Plus Power Setting

1-2

From Pin 5 of Power Connector (default)

2-3

From o3.3 V

Jumper

5 V Standby Power Setting

1-2

5 V IN to +5 V SB (default)

2-3

+5 V IN to N.C. (no connection)

Jumper

5 V Standby Power Setting

1-2

+5 VDC applied (default)

No voltage applied (pin 49 open)

Содержание EBC-C413




















































































Результаты поиска

Содержание EBC-C413

Отзывы:

Бренды по названию

Популярные бренды

WinSystems EBC-C413, Руководство по эксплуатации продукта

Результаты поиска

Содержание EBC-C413

Отзывы:

Бренды по названию

Популярные бренды