Winmate M-Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 112

Winmate M-Series Скачать руководство пользователя страница 101

USER MANUAL

CHAPTER 6

MOUNTING

- 101 -

CHAPTER 6: MOUNTING

This chapter provides mounting guide for all available mounting options. Pay attention
to cautions and warning to avoid any damages.

WARNING! / AVERTISSEMENT!

Follow mounting instructions and use recommended mounting
hardware to avoid the risk of injury.
Suivez les instructions de montage et d'utilisation recommandé le
matériel de montage pour éviter le risque de blessure.

6.1 Cable Mounting Considerations

For a nice look and safe installation, make sure cables are neatly hidden behind the
HMI device. Refer to

Chapter 2, section 2.1

for the cable installation instruction.

WARNING! / AVERTISSEMENT!

Observe all local installation requirements for connection cable type
and protection level.
Suivre tous les règlements locaux d’installations, de câblage et
niveaux de protection.

WARNING! / AVERTISSEMENT!

Turn off the device and disconnect other peripherals before
installation.
Éteindre l’appareil et débrancher tous les périphériques avant
l’installation.

ALTERNATING CURRENT / MISE À LE TERRE!

To prevent electrical shock, the Safety Ground location on the rear
must be bonded to the local earth ground through a minimum 12
AWG wire as short as possible
Pour éviter les chocs électriques, l

’emplacement de la prise terre à

l’arrière doit être lié à terre locale, à travers un 12 AWG minimum
et aussi court que possible.

«
...
99
100
101
102
103
...
»

Содержание M-Series

















































































































Отзывы:

Нет отзывов