Wincor Nixdorf TH420 Скачать руководство пользователя страница 52

Страница: 52 / 64

Status

LED behavior

Power off

Off

Firmware download

Fast blink

Level 0 diagnostics
(entered at power on or in reset)

Fast blink

Paper low
Temperature error
Voltage error

Slow blink

Cover open (receipt, slip or flip)
Paper out
Carriage jam
Slip jam
Flip jam
Knife jam

Fast blink

All other states

Test the receipt printer or slip printer by printing a sample test print as
described elsewhere in this document.

Determine if the condition is with the thermal receipt printer or the impact
slip printer and refer to the tables on the following pages.

If unexpected conditions arise while installing the USB driver, take a look in
USB Driver Installation, trou bles hoo ting.

Prin ter beeps

Condition

Possible causes

What to do

Printer beeps in a single,
double, or triple pattern at first
power on.The on-line, paper
status, error LED blinks in the
same pattern, and the printer
won’t power up.

The printer has a problem
with its electronics.

Contact a service
representative.

Printer beeps during normal
operation.

The printer may be
programmed to beep during
normal operation by the
software application used on
the host computer.

Consult your application
software manual.

TROUBLESHOOTING THE PRINTER

Содержание TH420

































































Результаты поиска

Содержание TH420

Отзывы:

Похожие инструкции для TH420

Бренды по названию

Популярные бренды

Wincor Nixdorf TH420, Руководство пользователя

Результаты поиска

Содержание TH420

Отзывы:

Похожие инструкции для TH420

Бренды по названию

Популярные бренды