Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 108 / 152

background image

TH210

Programmer’s Guide

104

n = 49 (ASCII n = 1) HEX 31

This command erases all 64K flash memory sectors allocated to user-defined character and logos
storage. Those sectors should be erased in two situations: when the logo definition area is full and
an application is attempting to define new logos, and when an application wants to replace one
user-defined character set with another. In both cases, all logos and character set definitions are
erased and must be redefined.

n = 50 (ASCII n = 2) HEX 32

This command erases all sectors available for user data storage.

n = 51 (ASCII n = 3) HEX 33

This command erases all sectors available for permanent fonts.
Erases a page of flash memory and sends a carriage return when the operation is complete.

Related information

See command “Flash memory user sectors allocation” (1D 22 55 n1 n2).
See also command “Expanded flash memory allocation” (1D 22 80) and “Select flash area” (1D 22
81 n).
Important: While erasing flash memory, the printer disables all interrupts, including
communications. To provide feedback to the application, the printer responds to the application
when the erase is complete with a 0D (Hex). After sending the erase user flash sector (1D 40 n)
command, an application should wait for the response from the printer before sending data.
Otherwise, data will be lost. If an application is unable to receive data, it should wait a minimum of
ten seconds after sending the erase user flash sector (1D 40 n) command before sending data.

Lock permanent font flash area

ASCII

GS 0xF0 0x10

n

Hexadecimal

1D F0 10

n

Decimal

29 240 16

n

Value of n:

n = 0x00

lock permanent font flash (default)

n = 0x01

unlock permanent font flash to erase or delete

This command allows or prevents the permanent font area to be erased.
Note: This only affects the 1D 40 33 commands and downloading a font to permanet font area
when a font already exists with the same ID.

Flash download

These commands are used to load firmware into the printer.
The commands are listed in numerical order according to their hexadecimal codes. Each command
is described and the hexadecimal, decimal, and ASCII codes are listed.
There are two ways to enter the download mode.

1.

While the printer is running normally, send the command, “Switch to flash download

mode” (1B 5B 7D) to leave normal operation and enter the download mode.

2.

If the flash if found corrupted during level 0 diagnostics the download mode is

automatically entered after the printer has reset.

«
...
106
107
108
109
110
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Canon Страницы: 58

image Prograf iPF680 Series

Бренд: Canon Страницы: 132

Бренд: Canon Страницы: 44

imageClass LBP6230dw

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 2

imageprograf IPF785

Бренд: Canon Страницы: 42

Бренд: Canon Страницы: 148

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 6

Color Bubble Jet BJC-1000 Series

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 105

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 68

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

imagePROGRAF iPF830

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды