Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 105 / 152

background image

TH210

Programmer’s Guide

101

n = 49 (ASCII n = 1) HEX 31

Loads active logo to flash memory. This is the default condition for logo flash storage. A logo
defined following this command is stored in flash memory.

n = 50 (ASCII n = 2) HEX 32

Loads user-defined characters to RAM only. This is the default condition for user-defined character
storage. Any user- defined characters defined following this command are not preserved over a
power cycle.

n = 51 (ASCII n = 3) HEX 33

Loads user-defined characters to flash memory. An application must use this command to store
user-defined characters in flash memory. Any user-defined characters defined following this
command are stored in flash memory. A user-defined character cannot be redefined in flash
memory. The flash memory page must be erased by an application before redefining user-defined
characters. For more information, see the erase user flash sector (1D 40 n) command.
Specifies whether to load the logos or user-defined characters to logo/font flash memory or to
RAM (volatile memory). The selection remains in effect until it is changed via this command or
until the power cycles. To specify permanent font flash, also send 1D 22 81 01.

Related information

This command is recognized in Native mode. In A793 and LEGACY emulations, parameter bytes go
into the print buffer.

Flash memory user sectors allocation

ASCII
Hexadecimal
Decimal

Value of

n1

:

Value of

n2

:

GS” U

n1

n

1D 22 55

n1 n2

29 34 85

n1 n2

1 (see below)

1 (see below)

n

1 is the number of 64k sectors used for logos and user-defined characters.

n

2 is the number of 64k sectors used for user data storage.

n1 + n2 <= 6 (dec) (1M)

n1 + n2

<= 22 (dec) 16 (hex) (2M)

If

n

1 +

n

2 is greater than the maximum number of sectors available, the command is ignored. The

printer returns NACK. Issuing this command with parameters different from current parameters
will erase all sectors. The printer returns ACK. Issuing this command with parameters the same as
current parameters will do nothing. The printer returns ACK.
Note: Flash memory is made up of user and program code. Therefore, the available flash memory
space will vary with the amount of program code utilized.

Flash object area pack

ASCII
Hexadecimal
Decimal

Value of

n1

:

GS” `

n1

1D 22 60

n1

29 34 96

n1

n

1 specifies

«
...
103
104
105
106
107
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

iPF650 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 40

iP90 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

iPF650 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 16

iP100 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

imageRUNNER ADVANCE C5560

Бренд: Canon Страницы: 67

imageRUNNER 3300

Бренд: Canon Страницы: 366

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 252

iPF710 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 2

Бренд: Panasonic Страницы: 155

Бренд: Panasonic Страницы: 160

Бренд: Pantum Страницы: 94

Бренд: VASTEX Страницы: 15

Бренд: TE Connectivity Страницы: 2

Бренд: TE Connectivity Страницы: 2

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды