Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 102 / 152

background image

TH210

Programmer’s Guide

98

lower right; and sets the absolute position in the horizontal when the starting position is set to the
upper right or lower left. The horizontal and vertical motion unit are specified by the set horizontal
and vertical minimum motion units (1D 50) command.
The set horizontal and vertical minimum motion units (1D 50) command can be used to change the
horizontal and vertical motion unit. However, the value cannot be less than the minimum
horizontal movement amount, and it must be in even units of the minimum horizontal movement
amount.

Formulas

[(

nL

+

nH

X 256) x (vertical or horizontal motion unit)] inches.

Exceptions

This command is effective only in page mode.
If the [(

nL

+

nH

X 256) x (vertical or horizontal motion unit)] exceeds the specified printing area,

this command is ignored.

Set relative vertical print position in page mode

ASCII
Hexadecimal
Decimal

Value

GS \

nL nH

1D 5C

nL nH

29 29

nL nH

The value for the horizontal and vertical movement cannot be less than the minimum horizontal
movement amount, and must be in even units of the minimum horizontal movement amount.
Sets the relative vertical print starting position from the current position. This command can also
change the horizontal and vertical motion unit. The unit of horizontal and vertical motion is
specified by this command.
This command functions as follows, depending on the print starting position set by select print
direction in page mode (1B 54):
When the starting position is set to the upper right or lower left of the printing area, the vertical
motion unit (

y

) is used. When the starting position is set to the upper left or lower right of the

printing area, the horizontal motion unit (

x)

is used.

Formulas

The distance from the current position is set to [(

nL

+

nH

x 256) x vertical or horizontal motion unit]

inches. The amount of movement is calculated only for the paper roll.
When pitch

n

is specified to the movement downward:

nL + nH

x 256 =

n

When pitch

n

is specified to the movement upward (the negative direction), use the complement

of 65536.
When pitch

n

is specified to the movement upward:

nL

+

nH

x 256 – 65536 –

N

Exceptions

This command is used only in page mode, otherwise it is ignored. Any setting that exceeds the
specified printing area is ignored.

«
...
100
101
102
103
104
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

I-Class Mark II

Бренд: Datamax Страницы: 12

Бренд: QMS Страницы: 27

Бренд: QMS Страницы: 3

Бренд: Oki Страницы: 222

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 160

Бренд: Konica Minolta Страницы: 15

Бренд: Panduit Страницы: 84

Бренд: J&Maya Страницы: 21

Бренд: Edimax Страницы: 93

Бренд: ABLE Systems Страницы: 12

Бренд: EFI Страницы: 4

Бренд: TAKE-A-LABEL Страницы: 12

apeosport-v c5585

Бренд: Fuji Xerox Страницы: 493

Бренд: Intermec Страницы: 2

Бренд: BIG TREE TECH Страницы: 11

Бренд: Xerox Страницы: 240

Accel-a-Writer 4

Бренд: Xante Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды