Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 101 / 152

background image

TH210

Programmer’s Guide

97

Sets the position and size of the printing area in page mode until the printer is initialized, reset, or
powered off, or a 0C command is sent.
The command can be sent multiple times so that several different print areas, aligned in different
print directions, can be developed in the printer’s page buffer before being printed using the print
page mode commands (0C or B 0C).

Formulas

The starting position of the print area is the upper left of the area to be printed (x0, y0). The length
of the area to be printed in the y direction is set to dy inches. The length of the area to be printed
in the x direction is set to dx inches. Use the equations to determine the Value of x0, y0, dx, and
dy.



x0 = [(

n

1 +

n

2 x 256) x (horizontal direction of the fundamental calculation pitch)]



y0 = [(

n

3 +

n

4 x 256) x (vertical direction of the fundamental calculation pitch)]



dx = [(

n

5 +

n

6 x 256) x (horizontal direction of the fundamental calculation pitch)]



dy = [(

n

7 +

n

8 x 256) x (vertical direction of the fundamental calculation pitch)]

Keep the following notes in mind for this command.



The fundamental calculation pitch depends on the vertical or horizontal direction.



The maximum printable area in the x direction is 576/203 inches.



The maximum printable area in the y direction is 576/203 inches.

See the illustration for a graphic representation of the printing area. For more information about
the fundamental calculation pitch, see the set horizontal and vertical motion units command (1D
50).

Maximum area specification in page mode

Maximizing the possible area in page mode consumes almost all of the free RAM. Without any free
RAM, bitmap rotations and enlargements cannot be performed. Use the User Storage Status
command (1D 97 m n) to determine the amount of free memory.

Exceptions

The command is effective only in page mode.
If [x0 + dx] is greater than the printable area, the printing area width is set to [horizontal printable
area – x0]. If [y0 + yx] is greater than the printable area, the printing area height is set to [vertical
printable area – y0].

Set absolute vertical print position in page mode

Sets the absolute vertical print starting position for buffer character data in page mode. The
absolute print position is set to [(

nL

+

nH

X 256) x (vertical or horizontal motion unit)] inches.

The vertical or horizontal motion unit for the paper roll is used and the horizontal starting buffer
position does not move.
The reference starting position is set by select print direction in page mode (1B 54). This sets the
absolute position in the vertical direction when the starting position is set to the upper left or

ASCII
Hexadecimal
Decimal

GS $

nL nH

1D 24

nL nH

29 36

nL nH

«
...
99
100
101
102
103
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Бренд: 3DP Страницы: 12

Бренд: IBM Страницы: 16

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 4

Бренд: TallyGenicom Страницы: 3

WorkCentre Pro 123

Бренд: Xerox Страницы: 4

DocuCentre SC2020

Бренд: Xerox Страницы: 322

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 80

Бренд: Xerox Страницы: 38

WorkCentre 7132

Бренд: Xerox Страницы: 73

Бренд: OKIDATA Страницы: 13

Бренд: Xerox Страницы: 418

Бренд: Copystar Страницы: 4

Бренд: Konica Minolta Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды