manualshive.com logo in svg

Winco Elevate BDC 2578, Руководство владельца по эксплуатации и обслуживанию

Поделиться
Скачать
Winco Elevate BDC 2578 Скачать руководство пользователя страница 13

Page 13 of 49

Document No.: 006020 
Revision: P 

OWNERS OPERATING & MAINTENANCE MANUAL

PHLEBOTOMY COLLECTION

Fig 1

Fig 2

Fig 3

CABINET ASSEMBLY AND INSTALLATION

* MODEL 2570

1. 

Remove the cabinet from the frame (

FIG 1

)Use 

CAUTION

 to avoid personal injury or damaging the 

product.

2. 

Remove packaging materials from cabinet assembly.

3. 

The cabinet installs on the 

PATIENT LEFT

 side of chair (

FIG 2

). Insert the cabinet assembly into the 

receiving tube. 

ALWAYS

 make sure that the slot in the Arm Assembly faces the knob installed on the 

receiving tube. (

FIG 2

)

4. 

Adjust the Cabinet to the desired height and tighten knob.

5. 

Cabinet installation is complete (

FIG 3

) 

Be sure to tighten the BLACK KNOB to secure the cabinet even if no height adjustment is made. 
This will ensure cabinet is secure for use.

2570 / 2571

Содержание Elevate BDC 2578





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды