Page 1 of 4
006250 Rev. T
04/23/20
NCG
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER place screen on a cart, table, stand or other objects; Screen could fall and INJURY MAY OCCUR.
3. NEVER place screen near open flame or over a radiator or heat register.
4. NEVER place screen in front of a door or exit sign; or during emergency screen could hinder evacuation.
5. SUFFOCATION DANGER to children if vinyl is not attached to screen; Screen could block nose and mouth
and prevent breathing. VINYL SCREEN IS NOT A TOY.
6. DO NOT allow children to play with screen. Screen could fall and INJURY MAY OCCUR.
7. Screen should ALWAYS be positioned on level surface.
8. NEVER stand or ride on screen legs; INJURY MAY OCCUR.
9. DO NOT use screen in or with ANY type of vehicle or trailer.
10. DO NOT attach objects to screen frame. Screen can tip over and INJURY MAY OCCUR.
11. Any screen with broken or missing parts, torn vinyl, or other visible damage should be removed from service
immediately.
12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
13. SAVE THESE INSTRUCTIONS for future reference and training.
14.
Both small and large magnets can pose dangers to kids and adults. Mishandling of magnets may
cause injury or property damages. Make sure to keep magnets away from people who are wearing
pacemakers or other medical devices. Also keep magnets away from CRT monitors, CRT TVs, and
other electronic devices
.
Screen Model: 3170B
Designer Three Panel Screen
Tools needed:
•
Scissors or Box Cutter
•
5/32 Allen Wrench (provided)
•
Phillips Screwdriver
1. After checking your product for any shipping damage, remove all packing material and hardware that was secured for
shipping. Cut tape and/or plastic with scissors using caution to prevent damage to the screen.
LEG INSTALLATION
(
SEE PHOTOS ON NEXT PAGE)
2. Using a Phillips Screwdriver, Install (2)
Screen Leg Reinforcement Tubes (#5)
between
Leg Frame Assemblies (#3)
using
4-Phillips Head Screws (5A),
one on each end, through
(#3)
into
(#5)
.
Leave screws on one
Leg Frame
Assemblies (#3)
loose to allow assembly to be inserted into
Wing/Mid Frame Assembly
(#1A).
3. Insert both
Leg Frame Assemblies (#3)
into the bottom of the
Wing/Mid Frame Assembly
(#1A).
Line up the holes in
(#3)
w/ the holes in
(#1A).
4. Using the
Allen Wrench
provided screw in
1-Button Socket Screw (3D),
per leg,
through
(#1A)
and into
(#3).
Tighten
2-
Phillips Head Screws (5A)
that were left loose in step 2.
PANEL REPLACEMENT
(
SEE PHOTOS ON NEXT PAGE)
5. To replace
Vinyl Panels (#4)
, hold the screen by the top
Screen Rod (#2A).
6. Next, using the
Allen Wrench
provided, push in on the small hole just below the
Snap Button (#2B).
Re-install
(#2A)
by repeating the above procedure, then release
(#2B)
when
(#2A)
is in place.
CARE AND MAINTENANCE OF YOUR SCREEN
7. Periodically check all fasteners for tightness.
8. To clean
Vinyl Panels
use only mild liquid soap and water.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions, contact Winco Customer Service at (800) 237-3377 or
e-mail: [email protected], before attempting to use this product; otherwise injury may occur.
Winco assumes no responsibility for damage or injury caused by the
improper assembly, installation, or use of these products.