background image

Whittier Finishing Hints

 

 

P.O. Box 2827 
Eugene, OR 97402 USA 
Toll Free: 800-653-3336 
Ph: 541-687-0213 
Fax: 541-687-2060 
www.whittierwood.com

 

 

Page 2 of 2 

 

Rev. 10/13

 

 

Preparing the surface

 

1. 

Sand each piece with #220 grit sandpaper. Sand with 
the grain of the wood on flat surfaces and opposite the 
grain on turnings. Some parts may be plywood. Be 
careful not to sand through the veneer. End grain such 
as table top ends, seat edges and grooves on turnings 
accept more stain. Extra sanding in these areas with 
#320 grit sandpaper reduces stain absorption and 
creates a more evenly stained piece. 
 

2. 

When sanding is completed, wipe the surface of your 
furniture with a lint-free rag or tack cloth. Make sure the 
item is free of dust before you proceed. 
 

Staining 

1. 

Always read and follow all label directions

. Stir the 

stain well before you start. Stir periodically throughout 
the duration of the project to maintain uniform color 
consistency. 
 

2. 

Test stain on an inconspicuous spot on your project. 
Put at least one coat of your top coat over the test area 
as it also affects the look of the stain. 

Test every type 

of wood that is in your kit. These are identified in the 
Assembly Instructions

 Different types of wood may 

react differently to the stain color. You might need to 
add a second coat of stain to lighter woods to match 
the darker woods in your kit. 
 

3. 

Apply stain with a poly brush or lint-free cloth. Apply 
stain over a small area and wipe off excess. Working in 
small areas will make the color easier to control. 

 

4. 

Cotton swabs are ideal for hard to reach areas. 
 

5. 

Allow the stain to dry thoroughly before you proceed.

 

 

Applying the top coat

 

1. 

Always read and follow all label directions

. Stir your top 

coat gently; do not shake. Shaking the can creates 
bubbles that are hard to remove. 
 

2. 

All surfaces including the underside of table tops and 
inside drawers must be sealed with at least one layer 
of a top coat. This will help minimize wood swelling, 
shrinkage, warping and cupping due to changes in 
moisture content or temperature. 
 

3. 

Apply a minimum of two coats when you use 
polyurethane or varnish (especially on all table top and 
work surfaces).  After allowing the first coat to dry, 
sand lightly with #320 grit sandpaper. Remove dust 
with a lint-free rag or tack cloth. For added protection, 

apply additional coats. Lightly sand and wipe surface 
with a lint-free rag or tack cloth between coats.  
 

4. 

Some finishes tend to slightly raise the grain. This can 
be easily controlled with a light sanding between coats. 
Do not use steel wool when you use water-based 
finishes. Strands of steel fiber caught in the wood can 
cause rust spots when coated with any water-based 
product. 
 

Painting

 

1. 

Always read and follow all label directions. 

Since there 

is a large variation between paint manufacturers and 
products, ask your paint supplier for specific advice on 
how to best use the paint you purchase. Ask them 
specifically for advice on finishing bare wood. 
 

2. 

First coat the wood with a primer. An oil based primer 
works best for a smooth finish. If you do not wish to 
use a solvent based primer, water based primer works 
almost as well. However it may raise the wood grain 
and require additional sanding. 
 

3. 

Buy quality brand paint in a satin, semi-gloss, or gloss 
sheen. Apply a second coat for a smooth finish. Lightly 
sand between coats using with #320 grit sandpaper so 
that the second coat will bond well. Be sure to use a 
tack cloth after sanding to remove any residue. Repeat 
as desired. 
 

4. 

 No top coat is required when using paint. 
 

 

Содержание 3505AUFb








Отзывы: