White Outdoor Z-185L, Z-205, Z-225 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 38

background image

OPERATOR’S MANUAL

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

PRINTED IN U.S.A.

Models

Z-185L

Z-205
Z-225

FORM NO. 770-10104A

Warning:

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.

WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722

(5/99)

1
2
3
...
»

Содержание Z-185L, Z-205, Z-225







































Отзывы:

Нет отзывов

Похожие инструкции для Z-185L, Z-205, Z-225

532 42 27-27 Rev. 2

Бренд: McCulloch Страницы: 28

Бренд: Salsco Страницы: 29

Бренд: Yard-Man Страницы: 36

Бренд: Jacobsen Страницы: 98

Бренд: Cub Cadet Страницы: 44

Бренд: Poulan Pro Страницы: 48

Super Surfer II GSKA1948S

Бренд: Great Dane Страницы: 78

Бренд: Cub Cadet Страницы: 40

Бренд: Kubota Страницы: 299

Бренд: ARNETOLI MOTOR Страницы: 2

Бренд: Worx Страницы: 52

Бренд: Murray Страницы: 68

Бренд: Cub Cadet Страницы: 36

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды