background image

Figure 3-

3

Setting Up 

Your Snow 

Thrower

WARNING

Never use your hands 
to clean snow and 
ice from the chute 
assembly or auger 
housing.

IMPORTANT

Under any circum-
stance do not exceed 
manufacturer’s recom-
mended psi. Equal tire 
pressure should be 
maintained at all times. 
Excessive pressure 
when seating beads 
may cause tire/rim 
assembly to burst 
with force sufficient to 
cause serious injury. 
Refer to sidewall of 
tire for recommended 
pressure.

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger 
housing and is designed to clear a clogged chute. Refer 
to page 11 for instructions on how to properly use it.

NOTE: 

 This item is fastened with a cable tie to the rear 

of the auger housing at the factory. Cut the cable tie 
before operating the snow thrower.

WARNING: Never use your hands to 
clean snow and ice from the chute 
assembly or auger housing.

Lamp Wiring Harness (If equipped)

The post on the cable tie attaching the lamp wiring 
harness to the lower handle should be plugged into the 
hole in the lower handle.  Pull the slack portion of the 
wiring harness through the cable tie to prevent interfer-
ence with the recoil starter handle.

Clean-Out 

Tool

Skid Shoes

Position the skid shoes based on surface conditions. 
Adjust upward for hard-packed snow. Adjust downward 
when operating on gravel or crushed rock surfaces. See 
“Making Adjustment” Section.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check 
the tire pressure before operating the snow thrower. Refer 
to the tire side wall for tire manufacturer’s recommended 
psi and deflate (or inflate) the tires as necessary.

NOTE

: If the tire pressure is not equal in both tires, the 

unit may not travel in a straight path and the shave plate 
may wear unevenly.

General Recommendations

1.  Always observe safety rules when performing  

any maintenance.

2.  The warranty on this snow thrower does not cover 

items that have been subjected to operator abuse 
or negligence. To receive full value from warranty, 
operator must maintain the snow thrower as  
instructed here.

3.  Some adjustments will have to be made periodically 

to maintain your unit properly.

4.  Periodically check all fasteners and make sure these 

are tight.

Figure 3-10

Содержание 31AE5LKH
























Отзывы: