background image

20101-5-0509

Page 8

The space in the above example is a confined space because the 

actual BTU/Hr used is more than the maximum BTU/HR the space 

can support. You must provide additional fresh air. Your options 

are as follows:

A.  Rework worksheet, adding the space of an adjoining room. If 

the extra space provides an unconfined space, remove door to 

adjoining room or add ventilation grills between rooms. See 

Ventilation Air From Inside Building. 

B.  Vent room directly to the outdoors. See V

entilation Air From 

Outdoors.

C.  Install a lower BTU/Hr heater, if lower BTU/Hr size makes 

room unconfined.

If the actual BTU/Hr used is less than the maximum BTU/Hr the 

space can support, the space is an unconfined space. You will need 

no additional fresh air ventilation.

WARNING: you must provide additional ventilation air 

in a confined space.

Ventilation Air

Ventilation Air From Inside Building (Figure 1)

This fresh air would come from an adjoining unconfined space. 

When  ventilating  to  an  adjoining  unconfined  space,  you  must 

provide two permanent openings: one within 12" of the ceiling 

and one within 12" of the floor on the wall connecting the two 

spaces (see options 1 and 2, Figure 1). You can also remove door 

into adjoining room (see option 3, Figure 1). Each ventilation grill 

or opening shall have a minimum free area of one square inch per 

1,000 BTUH of the total input rating of the gas equipment in the 

confined space.

Figure 1

WARNING:  Rework worksheet, adding the space of the 

adjoining unconfined space. The combined spaces must have 

enough fresh air to supply all appliances in both spaces

.

Ventilation Air From Outdoors (Figure 2)

Provide extra fresh air by using ventilation grills or ducts. You must 

provide two permanent openings: one within 12" of the ceiling 

and one with 12" of the floor. Connect these items directly to the 

outdoors  or  spaces  open  to  the  outdoors. These  spaces  include 

attics and crawl spaces. In most cases for direct communication 

with the outdoors or direct communication through a vertical duct 

a free area opening of one square inch per 4,000 BTU/Hr of heater 

input rating for each grill. If a horizontal duct is used, a grill free 

area or duct opening shall have a free area opening of one square 

inch per 2,000 BTU/Hr for each grill. Follow the 

National Fuel 

Code ANSI Z223.1/NFPA54, Air for Combustion and Ventilation

 

for required size of ventilation grills or ducts.

IMPORTANT:

 Do not provide openings for inlet or outlet air into 

attic if attic has a thermostat-controlled power vent. Heated air 

entering the attic will activate the power vent.

Figure 2

PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR

 (continued)

Содержание VFP32FP(20





























Отзывы: