WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 34

Страница: 34 / 194

WhitakerAudio

PWB Design

The 20 W Stereo Amplifier is comprised of three major PWB groups, specifically:

•

The amplifier module, which includes amplifier board #1 (right), amplifier board #2 (left),

the B+ rectifier board, and a pair of speaker terminal boards.

•

The preamplifier power supply module.

•

The power management module.

Each of these modules are described in the following sections.

3.1

20 W Stereo Amplifier Module

A printed wiring board (PWB) implementation is used that incorporates all components of the

stereo amplifier, except for the transformers, which are mounted on the chassis. The amplifier

module includes amplifier board #1 (right), amplifier board #2 (left), the B+ rectifier board, and a

pair of speaker terminal boards. Each is described in the following sections.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды