WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 104

Страница: 104 / 194

104

WhitakerAudio

the bottom chassis plate. After each terminal is attached to a lead, gently pull on the wire and

terminal to make sure a good crimp has been made.

– Connect PL1 – output transformer plate 1 connection. Find the

blue

wire from the left

channel output transformer (T2). Install a connector to the end of the wire. Attach to the

PL1

post on the left channel PWB.

– Connect SC1 – output transformer screen 1 connection. Find the

blue/yellow

wire from

the left channel output transformer. Install a connector to the end of the wire. Attach to the

SC1

post on the left channel PWB.

– Connect PL2 – output transformer plate 2 connection. Find the

brown

wire from the left

channel output transformer. Install a connector to the end of the wire. Attach to the

PL2

post on the left channel PWB.

– Connect SC2 – output transformer screen 2 connection. Find the

brown/yellow

wire from

the left channel output transformer. Install a connector to the end of the wire. Attach to the

SC2 post on the left channel PWB.

– Connect T2ct – output transformer center tap. Find the

red

wire from the left channel

output transformer. Install a connector to the end of the wire. Attach to the

T2ct

post on

the left channel PWB.

Double-check the connections from the left channel output transformer to the PWB.

5.6.7.4

Power Transformer Leads

In the following steps, trim the transformer lead lengths so the wires will comfortably reach their

respective terminals. After each terminal is attached to a lead, gently pull on the wire and terminal

to make sure a good crimp has been made.

– Connect 400V – plate winding. Find one of the two

red

leads from the power transformer

(T51). Install a connector to the wire. Attach to one of the

400V

posts on the rectifier

PWB.

– Connect 400V – plate winding. Find the other

red

lead from the power transformer. Install

a connector to the wire. Attach to the available

400V

post on the rectifier PWB.

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды