WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier Скачать руководство пользователя страница 100

Страница: 100 / 194

100

WhitakerAudio

– Locate the power supply choke, L51. Examine the mounting holes. Note that two holes are

provided within the confines of the base of the choke. These holes are used for two of the

support standoffs for the power management PWB. Install the 2.5-inch standoff using

countersunk 3/8-inch long #6 screws. Include a lockwasher between the chassis and the

standoff. Tighten.

– Install the power supply choke using the #6 hardware provided, carefully guiding the leads

through the hole in the chassis. Be sure to include the grounding lug wire. Route the

grounding wire through the chassis along with the choke leads.

All of the transformers have now been installed.

5.6.6

Install Remaining Chassis Components

Locate the remaining chassis-mounted components, which include the following:

•

Panel-mount potentiometer R55

•

Top chassis decal

– Mount R55 –

100

potentiometer

– Hum Balance Control. Mount the device from the

top of the chassis and secure with the lockwasher and nut provided. Position the device so

that when at the center of travel, the white dot on the knob points toward the back of the

chassis.

– Carefully peal off the backing for the top chassis decal. Position it on top of the chassis,

behind tubes V5 and V6. Apply the decal.

5.6.7

Wire the Transformer Leads

Find the female “quick-disconnect” connectors. In the following steps, the transformer leads will

be connected to their respective terminals on the circuit boards using these connectors. The lead

lengths from the various transformers may need to be trimmed to remove excess length. Make

sure to keep sufficient lead length to permit organized cable routing.

5.6.7.1

Cable Organization

To facilitate cable organization, it is advisable to install expandable flexible cable sleeving on

some of the transformer leads. A supply of this material is provided. To properly perform the

following steps, it will be necessary to have a heat gun on hand. (A common hair dryer may be

Содержание J C Whitaker 20 W Stereo Audio Amplifier



































































































































































































Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды

WhitakerAudio J C Whitaker 20 W Stereo Audio Amplifier, Руководство пользователя

Результаты поиска

Содержание J C Whitaker 20 W Stereo Audio Amplifier

Отзывы:

Похожие инструкции для J C Whitaker 20 W Stereo Audio Amplifier

Бренды по названию

Популярные бренды