background image

Page 8 | 1-800-343-9463

QS

 021616

BEFORE YOU START 

1. Inspect the system before installation. If damage is found, please contact your distributor or WhisperKOOL 

Customer Service at 1-800-343-9463.

2. The Quantum Evaporator unit requires a dedicated 115V, 15 amp dedicated circuit
3. The 9000 condensing unit requires a dedicated 230V 15 amp, single phase dedicated circuit.  

Use a surge protector with the unit. Do not use a GFI (Ground Fault Interrupter) line.

4. The 12000 condensing unit requires a dedicated 230V 20 amp, single phase dedicated circuit
5. It is REQUIRED to install a drain line to remove condensation from the evaporator unit.
6. The system is intended for use in properly designed and constructed wine cellars. Hire a professional wine 

storage consultant with a valid contractor’s license to build your wine cellar.

7. WhisperKOOL requires that all Split Systems be installed by a certified HVAC-R technician only.
8. Warranty is not active until a Warranty Checklist has been received, reviewed, and approved.

If you encounter a problem with your WhisperKOOL system, please refer to the Troubleshooting Guide on page 30. 

If you have any further questions, concerns, or need assistance, please contact WhisperKOOL’s Customer Service at 

1-800-343-9463. Please be sure all testing has been completed prior to contacting Customer Service. Please have your 

results ready for your representative.

Содержание Quantum SS12000









































Отзывы: