Whirlpool WTW4715EW, Инструкция по использованию и уходу

Страница: 9 / 35

9
Operate your washer only when you are home. If moving, or
not using your washer for a period of time, follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer to avoid flooding due
to water-pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1.
Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on Rinse & Spin cycle for about 30 seconds
to mix antifreeze and remaining water.
3.
Unplug washer or disconnect power.
NON-USE AND VACATION CARE
WASHER CARE (cont.)
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach
compartment.
NOTE: Use of more liquid chlorine bleach than
recommended above could cause washer damage over
time.
c. Close the washer lid.
d. Do not add any detergent or other chemical to the washer
when following this procedure.
e. Select the cycle recommended for cleaning the inside of
the washer.
f. Press the START/Pause button to start the cycle.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press START/Pause once or twice
(depending on model). After the cycle has stopped, run a
Rinse & Spin cycle to rinse cleaner from washer.
Cleaning the Dispensers
After a period of using your washer, you may find some residue
buildup in the washer’s dispensers. To remove residue from
the dispensers, wipe them with a damp cloth and towel dry.
Do not attempt to remove the dispensers or trim for cleaning.
The dispensers and trim are not removable. If your model has
a dispenser drawer, however, remove the drawer and clean
it before or after you run the Clean Washer cycle. Use an all-
purpose surface cleaner if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills. Use
only mild soaps or cleaners when cleaning external washer
surfaces.
IMPORTANT: To avoid damaging the washer’s finish, do not
use abrasive products.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water-
inlet hoses.
2.
If washer will be moved during freezing weather, follow
"Winter Storage Care" directions under "Washer Care"
before moving.
3. Disconnect drain hose from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4.
Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials back
inside washer. If you do not have packing tray, place heavy
blankets or towels into basket opening. Close lid and place
tape over lid and down front of washer. Keep lid taped
until washer is placed in new location. Transport washer in
upright position.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2.
Before using again, run washer through the following
recommended procedure:
To use washer again:
1.
Flush water pipes and hoses. Reconnect water-inlet hoses.
Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through Bulky Items/Sheets cycle to clean
washer and remove antifreeze if used. Use half the
manufacturer’s recommended amount of detergent for a
medium-size load.