Whirlpool WSE 2930 W Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 101

background image

Functional characteristics

Dispenser heater

According to product model, one or two heater can be
attached to the User Interface board.

Heaters state will be set according to what communicated
by the Main Control board (User Interface board is not
provided with EEPROM so the heaters state will be stored
by Main Control board in case of a main power failure and
communicate when power is restored).

The state of the heaters can be toggled between on or off
pressing the virtual button 2.

No heaters state feedback is foreseen.

Heaters must always be turned off when other loads are
turned on (dispenser light and/or step motor) and during
the start up procedure, i.e. the heaters will be turned on
after 10 seconds and anyway after the initial start up of the
stepper motor has finished.

Heater default state will be set to ON when the system
start.

«
...
51
52
53
54
55
...
»

Содержание WSE 2930 W






































































































Отзывы:

Нет отзывов

Похожие инструкции для WSE 2930 W

Бренд: V-ZUG Страницы: 24

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 10

Бренд: ZANKER Страницы: 14

Бренд: Marvel Страницы: 1

Бренд: Galaxy Страницы: 64

Бренд: Zanussi Electrolux Страницы: 16

Бренд: Smeg Страницы: 16

Бренд: German pool Страницы: 28

Бренд: ZANKER Страницы: 18

Бренд: CORBERO Страницы: 18

Бренд: Indesit Страницы: 16

Бренд: UNITED Страницы: 22

Бренд: ZANKER Страницы: 56

Бренд: U-Line Страницы: 14

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 48

Бренд: Zanussi Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды