Whirlpool WSE 2930 W Скачать руководство пользователя страница 25

Страница: 25 / 101

Operation

Indication of Water Filter

By pressing the “reset alarm” button for at least 3 seconds the buzzer sounds one time. The water filter icon
switch back to the low usage state.

The water filter control will calculate and record the total volume of water flowed through the valve during the

opening periods. The flow rate for the dispenser water valve is 1,51 litres per minute (24-58 cc per second).

The total liters flow is calculated by using the flow rates for Ice Maker valve and Water Dispenser valve.

The litres of each valve flow rate is multipled by the corresponding open time. The total liters

will be obtained adding the liters of each valve. The liters and time usage data will be recorded even after

a power black out. These data will be updated daily.

Содержание WSE 2930 W






































































































Результаты поиска

Содержание WSE 2930 W

Отзывы:

Похожие инструкции для WSE 2930 W

Бренды по названию

Популярные бренды

Whirlpool WSE 2930 W, Руководство пользователя

Результаты поиска

Содержание WSE 2930 W

Отзывы:

Похожие инструкции для WSE 2930 W

Бренды по названию

Популярные бренды