Whirlpool Cabrio,- WTW6200V, Руководство по установке

Страница: 4 / 20

4
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room,
closet, or recessed area. See “Drain System.”
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
A water heater set to deliver 120°F (49°C) water to the
washer.
A grounded electrical outlet located within 4 ft (1.2 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
Hot and cold water faucets located within 3 ft (900 mm) of the
hot and cold water fill valves, and water pressure of
20-100 psi (138-690 kPa) for best performance.
A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on carpeting is not
recommended.
A sturdy floor to support the washer weight (washer, water,
and load) of 315 lbs (143 kgs).
Do not store or operate your washer in temperatures at or below
32°F (0°C). Some water can remain in the washer and can cause
damage in low temperatures. See “Washer Care” for information
on winterizing.
Installation spacing for recessed area and closet
installations
The following spacing dimensions are recommended for this
washer. This washer has been tested for installation with spacing
of 0" (0 cm) clearance on the sides. Recommended spacing
should be considered for the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
*Required spacing
Drain System
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need.
See “Tools and Parts.”
Standpipe drain system—wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (51 mm) The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2" (51 mm) diameter to 1" (25 mm)
diameter standpipe adapter kit is available. See “Tools and
Parts.”
The top of the standpipe must be at least 39" (990 mm) high
and no higher than 96" (2440 mm) from the bottom of the washer.
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 39" (990 mm) above the floor
and no higher than 96" (2440 mm from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (710 mm) from the
bottom of the washer. Additional hoses might be needed.
A. Front view
B. Side view
C. Closet door with vents
A
B
C
17"*
(431.8 mm)
1"
(25 mm)
1"
(25 mm)
27 "
(699 mm)
1"*
(25 mm)
27"
(686 mm)
5"*
(127 mm)
14"* max.
(356 mm)
3"*
(76 mm)
3"*
(76 mm)
24 in. *
(155 cm )
2
2
48 in. *
(310 cm )
2
2
A
B
39"
(990 mm)
C
D
39"
(990 mm)
28"
(710 mm)
1 ⁄
2