SAVE THIS INSTRUCTION!
Westinghouse , and “You can be sure... if it's Westinghouse“
are
trademarks of Westinghouse Electric Corporation and are
used under license by The NCC
Manufactured and Distributed by: The NCC
Brooklyn, NY 11220 • www.thencc.com
Made in China
Outdoor Wireless Remote Control
Keychain transmitter activates remote base through walls, windows,
from your car or garage, up to 100ft. (30.5m) away.
Problem
Solution
The receiver doesn’t
Make sure the AC power cord is securely plugged into an
turn on
AC power outlet.
Unplug the unit for a moment, and then plug it back in again.
Check the outlet by plugging in another device.
The remote doesn’t work
Make sure the battery is fresh.
Stand closer to the receiver, the range should be up to 100ft.
Doors or Walls will reduce the remote distance.
Tr
ou
bl
es
ho
ot
in
g
Ti
ps
:
Customer Service Assistance: Toll Free 1-800-730-3707
Hours of Operation – 10AM to 6PM, EST, Monday - Friday
INSTRUCTIONS:
1. Plug the cord on the Remote Base into a grounded 3-prong outlet.
2. Plug your electrical device(s) into the Remote Base. Be sure that your electrical
device is powered ON.
3. Use the buttons on the Remote Control to turn your device(s) ON and OFF. If using
outdoors, be sure to plug into a GFCI approved outlet.
COMMAND1 TRANSMITTER PAIRING:
Note: Your Command1 Transmitter and reciever contained in this package are
pre-programmed and ready to use. Command1 Pairing is only required for using
additional transmitters.
This unit is equipped with patented Command1 technology. All Westinghouse indoor
and outdoor transmitters have the ability to be paired with all Westinghouse indoor and
outdoor receivers. Please follow the directions below to pair a transmitter to your
receiver.
1. Locate the power [ON/OFF] button on the receiver.
2. Press and hold the power button for 3 seconds. The LED power
indicator will begin to flash slowly.
3. On your transmitter, press [ON] wait 2 seconds and then press [OFF].
The LED indicator will now stop flashing.
4. You have successfully paired the transmitter to your receiver.
RESETTING THE UNIT
You can reset and remove all paired transmitters on your receiver by doing the
following:
1. Press and hold the ON/OFF button for 3 seconds. The LED indicator will begin to
flash slowly. Continue to hold for an additional 3 seconds. The LED indicator will
now begin to flash rapidly. Release the ON/OFF button for 1 second and press once
again to confirm reset. The LED indicator should now be OFF.
2. Your unit has now been reset and does not have any paired transmitters. (Note:
After reset, pairing is required to use the transmitter shipped in this package.)
BATTERY REPLACEMENT:
The Remote Control uses a 3 volt CR2032 lithium battery. To replace, slide off the
battery cover on the back of the transmitter. Insert a new CR2032 lithium battery,
making sure to match up the + and - polarity markings. To test, press the ON or OFF
buttons to make sure the LED lights up. Slide the cover back in. Do not dispose of
batteries in fire. Batteries may explode or leak.
28070-4 Wireless Remote Control System
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
The users manual or instruction manual for an intentional or unintentional radiator
shall caution the user that changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
4. Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
DO NOT splice, repair, or modify. Unplug when not in use. Fully insert plug. DO NOT
use damaged remote sets. Inspect periodically. Use within the electrical rating
marked on the remote set. DO NOT plug in more than a total of 1000 watts in this
remote set. If watts are not marked on appliance, multiply ampere rating (on
nameplate) by 125 to determine equivalent watts. Add determined watts for each
plugged-in appliance or lamp (sum of watts on bulbs) to find total watts being used.
Operating temperature range 0°C (32°F) to 45°C (113°F).
• Only use the batteries specified and be sure to match the + and - polarity
markings.
• Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline
batteries.
• Remove exhausted or dead batteries from the product.
• Remove batteries if product is not to be used for a long time.
• Do not dispose of batteries in fire. Batteries may explode or leak. As with all
small items, these batteries should be kept away from children. If swallowed,
seek medical attention immediately.
*This item is a Radio Frequency Device (RF), and as such the range of the remote
control is dependent on many factors. Actual operational distance will vary based on
walls and line of sight obstructions, and other nearby electronic devices.
One grounded outlets
Manual ON/OFF button on unit
Photocell Option - Turns lights off at dawn even when you forget
Transmitter works through Walls and doors - 80ft Range
LED Active Indicator
Transmitter uses a CR2032 3V lithium button cell battery
Specifications:
125VAC/60Hz/8A/1000W Resistive
8A/1000W Tungsten
6in (15.3cm) AWG 18/3 SJTW Vinyl Cord
