Western Digital WD RE3 XL333M Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 59

background image

Installation and Setup Procedures

WD RE3 XL333M

40

RELEASED 11/13/08 (WD CONFIDENTIAL)

2679-701179-A01

5.0

I

NSTALLATION

AND

S

ETUP

P

ROCEDURES

Hard drives are precision instruments that must be handled with care to prevent damage. It is
important to understand that drives are typically damaged because of Electrostatic Discharge (ESD),
rough handling, or shock and vibration. Refer to the latest version of the WD Drive Handling Guide
(2579-001027) for detailed instructions on all phases of drive handling.

Refer to

support.wdc.com/warranty

for detailed instructions on all phases of repackaging the drive.

5.1

Unpacking

5.1.1

Handling Precautions

WD products are designed to withstand normal handling during unpacking and installation.
Take care to avoid excessive mechanical shock or electrostatic discharge (ESD), which can
permanently damage the hard drive and void the warranty. Hard drives are typically damaged
because of ESD, rough handling, or shock and vibration.

To avoid ESD problems, wear a properly grounded wrist strap when handling the hard drive.
Articles of clothing generate static electricity. Do not allow clothing to come in direct contact
with the hard drive or circuit board components.

When the WD drive is not in its shipping container or installed in its proper host enclosure, it
must remain in the antistatic bag. To prevent damage, do not unpack your WD drive until you
are ready to install it.

5.1.2

Inspection of Shipping Container

Carefully examine the container for obvious shipping damage, such as: holes, signs of
crushing, or stains. Notify the carrier and your WD representative if you observe any shipment
damage. Always move the shipping container in the upright position indicated by the arrows
on the container.

5.1.3

Removal From Shipping Container

Remove the WD drive from the shipping container only for inspection or installation. Carefully
open the box. When removing the WD drive from the box, follow these precautions:

Grasp the drive by the sides only; avoid touching the circuit board components.

Gently place the drive on its antistatic bag on a clean, level, grounded work area.

Do not stack drives or stand the WD drive on its edge.

Important:

If your system does not support hot plugging (see “Hot Plug Support” on

page 23), it must be turned off and unplugged before installing your hard drive.

CAUTION:

When removing the drive from the shipping container, be careful not to drop it.

Dropping the drive can severely damage the head disk assembly or printed circuit board.

«
...
46
47
48
49
50
...
»

Содержание WD RE3 XL333M




























































Отзывы:

Нет отзывов

Похожие инструкции для WD RE3 XL333M

Бренд: Canon Страницы: 11

301160U - 1TB Ethernet Disk RAID Network Attached...

Бренд: LaCie Страницы: 5

Бренд: LaCie Страницы: 6

Бренд: Seville Classics Страницы: 2

Бренд: Dell EMC Страницы: 70

Бренд: NEC Страницы: 254

Бренд: Patiowell Страницы: 38

Do It Yourself Workbench EI-PT1013

Бренд: Excalibur Страницы: 2

HTS541680J9SA00 - Travelstar 80 GB Hard Drive

Бренд: Hitachi Страницы: 167

HTS541616J9AT00 - Travelstar 160 GB Hard Drive

Бренд: Hitachi Страницы: 2

HTS721010G9AT00

Бренд: Hitachi Страницы: 2

HTS541616J9AT00 - Travelstar 160 GB Hard Drive

Бренд: Hitachi Страницы: 188

HTS722010K9A300

Бренд: Hitachi Страницы: 2

Бренд: Weka Страницы: 20

Бренд: Viking Страницы: 33

Бренд: SmartStore Страницы: 16

Бренд: Spectra Logic Страницы: 21

T-Series Spectra T200

Бренд: Spectra Logic Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды