Western Digital Ultrastar Data102 Скачать руководство пользователя страница 72

Страница: 72 / 79

Installation Guide

5. Installation

5.2 Ultrastar Data102 Installation Procedure

Figure 46:

Shipping Bracket Screw Locations (CMA Standard)

Figure 47:

Shipping Bracket Screw Locations (CMA Lite)

Step 25 :

Plug the enclosure power cords into a PDU to power the enclosure.

Step 26 :

Double check the power indicators and other LEDs to ensure that the system is booting.

5.2.1

Special Considerations for Cable Routing

There are a number of special considerations installers should take when routing cables through the CMA.

This section outlines those considerations.
The distance from the end of the connector at the port to the first basket on the CMA should be 20” – 21”

long. This will give the cables enough slack at this end to prevent stress on the port and binding during

operation cycles.

Содержание Ultrastar Data102
















































































Результаты поиска

Содержание Ultrastar Data102

Отзывы:

Похожие инструкции для Ultrastar Data102

Бренды по названию

Популярные бренды

Western Digital Ultrastar Data102, Руководство по установке

Результаты поиска

Содержание Ultrastar Data102

Отзывы:

Похожие инструкции для Ultrastar Data102

Бренды по названию

Популярные бренды