background image

4

6650-2223

Note. Fibre Optic Handling

Fibre optic equipment requires  careful handling  as the fibre components are very 
sensitive to dust and dirt. If the fibre is disconnected from the modem, the protective 
plug on the transmitter/receiver must be replaced. The protective plug must be kept on 
during transportation. The fibre optic cable must also be protected in the same way.
If this recommendation is not followed, it can jeopardise the warranty.

Cleaning of the optical connectors

In the event of contamination, the optical connectors should be cleaned by using forced 
nitrogen and some kind of cleaning stick.
Recommended cleaning fluids:
• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol
• Hexane
• Naphtha

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified 
conditions.

Agency approvals and standards compliance

FCC Part 15.105 
Notice:

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely 
to cause harmful interference in which case the user will be required to correct the 
interference at his own expense.

EN 55022 Notice:

This is a class A product. In a domestic environment this product may cause radio inter-
ference in which case the user may be required to take adequate measures.

Type

Approval / Compliance

EMC

EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 55022, Emission IT equipment, class A

EN 55024, Immunity IT equipment

FCC part 15 Class A

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

Safety

EN 60950-1, IT equipment

Содержание ODW-621





















Отзывы: