Westell ProtectLink VHF-UHF Скачать руководство пользователя страница 95

Страница: 95 / 100

VHF-UHF Bi-Directional Amplifier Installation and Users Guide

System Software Upgrade: 6.2 System Reboot and Factory Reset

WESTELL.COM

1-800-377-8766

Page 6-3

6.2 System Reboot and Factory Reset

Rebooting the System

Click the

SYSTEM REBOOT

button to undertake a

system reboot. The

SYSTEM REBOOT

popup will

appear as shown at right. If the system includes
multiple devices which can be rebooted, the user
must select the desired device with the selection
menu. Click

SYSTEM REBOOT

to proceed with

the reboot.

When the BDA is rebooted, service will be disrupted during the reboot, but all
configurations and alarm history will be preserved.

Factory Reset

Click the

FACTORY RESET

button to reset the

system to factory defaults. The FACTORY RESET
popup will appear as shown at right. Click
FACTORY RESET to undertake the reset.

CAUTION:

BDA service will be disrupted when a
factory reset is undertaken, and all
configuration and alarm history will be lost.

Содержание ProtectLink VHF-UHF





































































































Результаты поиска

Содержание ProtectLink VHF-UHF

Отзывы:

Бренды по названию

Популярные бренды

Westell ProtectLink VHF-UHF, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ProtectLink VHF-UHF

Отзывы:

Бренды по названию

Популярные бренды