Instruction Manual & Warranty
TE55WHB
Limited One Year Warranty
AmerTac
™
warrants this product to be free from defects in material and
workmanship for a period of one year from the date of purchase. AmerTac’s
obligations are limited to repairing or replacing any defective unit and are
effective only if such units are returned within one year of the purchase
date to AmerTac, Saddle River Executive Centre, One Route 17 South, Saddle
River, NJ 07458. Warranty void if damage is due to misuse or improper
installation. In no circumstance will AmerTac be liable for consequential or
incidental damages relating in any way to this product.
Garantía limitada de un año
AmerTac™ garantiza que este producto está libre de defectos de material
y mano de obra por un período de un año a partir de la fecha de compra.
Las obligaciones de AmerTac se limitan a reparar o cambiar la unidad
defectuosa y son efectivas sólo si se devuelve en un lapso de un año a partir
de la fecha de compra a AmerTac, Saddle River Executive Centre, One Route
17 South, Saddle River, NJ 07458. La garantía no será válida si el daño es
causado por mal uso o instalación inadecuada. En ningún caso AmerTac
será responsable por daños consecuentes o incidentales relacionados en
cualquier forma con este producto.
Garantie limitée d'un an
AmerTac™ garantit ce produit contre tout défaut de matériaux et de main
d’œuvre pendant une période de un (1) an à partir de la date d’achat. Les
obligations d’AmerTac se limitent à la réparation ou au remplacement de
tout article défectueux et s’appliquent seulement si l’article est retourné
dans l’année de sa date d’achat à AmerTac, Saddle River Executive Centre,
One Route 17 South, Saddle River, NJ 07458. AmerTac ne peut en aucun
cas être tenue responsable pour des dommages consécutifs ou accessoires
liés de quelque manière que ce soit à ce produit.
Questions?, ¿Preguntas? 201.661.9944
©2010 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
www.amertac.com
Made in China
Fabriqué en Chine/Hecho en China
I09-0033-A
THIS TIMER IS FOR INDOOR USE ONLY
– DO NOT USE IN
WET LOCATIONS.
THIS TIMER HAS A BUILT-IN RECHARGEABLE BATTERY THAT IS
USED TO RETAIN THE CURRENT TIME AND ON/OFF SETTINGS
WHEN UNIT IS NOT PLUGGED INTO AN OUTLET OR DURING
POWER FAILURE.
Activating Timer
1.
Display
– Remove plastic display protection from front
of display.
2.
Installation
– Plug timer into an outlet and wait for at
least 30 minutes to charge the built-in rechargeable battery.
3.
Set Current Time
– While holding down CLK (Clock) button,
press DAY, HOUR and MIN (Minute) buttons respectively to set
the weekday, hour and minute. Note that AM or PM appears
after the time.
Your timer is now ready to be programmed.
Programming Events
1. Press PROG button once, display
will look as shown in Figure 1,
indicating ON programming of timer
setting 1.
2. Press DAY button until the display shows the day(s) you
want timer to turn ON.
- All days of the week (MO TU WE TH FR SA SU)
- Any single day of the week (for example WE)
- Weekdays only (MO TU WE TH FR)
- Weekends only (SA SU)
3. Press HOUR and MIN buttons to select time of day to turn
timer ON – press HOUR button to change from AM to PM.
4. Press PROG button again, display
will look as shown in Figure 2,
indicating OFF programming of timer
setting 1.
5. Repeat steps 2 and 3 to set day(s) and time you want
timer to turn OFF.
6. To set additional ON/OFF cycles (maximum of 7 events) press
PROG button and follow procedures in steps 2 to 5 for each
new ON/OFF event. When finished, press CLK button – display
will show current time. Timer will control the device plugged
into it according to the programmed events.
Reviewing Events
Pressing PROG button to cycle through all programmed ON/OFF
events. Press CLK to return to normal operation.
Clearing Programmed Events
Press PROG button to locate the ON/OFF event to be cleared.
While holding MODE button down, press PROG to clear settings
for that event.
Activating Events
Automatic
– For automatic operation of programmed events,
press MODE button until AUTO is displayed.
Random
– For random operation, press MODE button until
RDM is displayed. Timer will turn ON and OFF at +/– 30 minutes
of programmed events randomly.
Manual
– For manual operation, press MODE button until
ON (to turn and remain on) or OFF (to turn and remain off) is
displayed.
Operating Timer
Plug timer into AC outlet. Plug lamp or appliance to be controlled
into timer. Check and adjust timer setting as required.
Specifications:
120V~, 60Hz
15A, 1800W Resistive
8.3A, 1000W Tungsten
Figure 1
MO TU WE TH FR SA SU
ON
Figure 2
MO TU WE TH FR SA SU
OFF
Indoor
Digital Timer
with grounded outlet
IMPORTANT NOTES
DO NOT EXCEED RATING OF TIMER – 1800 WATTS FOR
RESISTIVE LOADS AND 1000 WATTS FOR TUNGSTEN
LOADS (SUCH AS LIGHTING).
