12
5
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN THE
POWER CORD on page 7.) If an extension cord is needed, use only a 14-gauge cord of five feet (1,5 m) or
less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. (See
step 1 on page 9.)
c. Check the circuit breaker located on the treadmill near the
power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit
breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 9.)
d. If the treadmill still will not run, please call our Customer Service Department.
3. SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY
a. Check the batteries in the console. (See BATTERY INSTALLATION on page 8.) Most problems are the re-
sult of drained batteries.
4. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON
a. If an extension cord is needed, use only a 14-gauge cord of five feet (1,5 m) or less in length.
b. If the walking belt still slows when walked on, Customer Service Department.
5. SYMPTOM: THE WALKING BELT IS OFF-CENTRE WHEN WALKED ON
a. If the walking belt has shifted to the left, first remove the key
and
UNPLUG THE POWER CORD
. Using the 3/16Ó end of the
allen wrench, turn the left rear roller adjustment bolt clockwise
1/4 of a turn. Plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is cen-
tred.
Tripped
Reset
Tripped
Reset
c
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly requires the following tools: The in-
cluded allen wrench, your own phillips screwdriver and an adjustable spanner .
1. With the help of a second person,
carefully
lay the
treadmill on its side. Insert a Leg (95) into the treadmill
as shown. Using an adjustable spanner, attach the Leg
with two of the eight Upright Screws (50). Be sure to start
both Screws before tightening either one, and push on
the heads of the Screws whilst tightening them.
Lay the treadmill on its other side. Attach the other Leg
(95) as described above.
Press two Leg Pads (97) onto each Leg (95) as shown.
Note: One extra Leg Pad may be included.
During as-
sembly, be careful to avoid dislodging the Leg Pads.
2. With the help of a second person,
carefully
raise the
treadmill to the upright position so the Legs (95) are rest-
ing flat on the floor. Next, lower the deck to the position
shown.
Attach one of the Handrails (51) to the left Upright (1) with
two Upright Screws (50) and a Washer (82). Be sure to
start both Screws before tightening either one, and push
on the heads of the Screws whilst tightening them.
Note:
Refer to drawing 3 below. Note the opening near the
upper end of the right Handrail (51). If only one
Handrail has an opening, attach that Handrail to the
Right Upright (1). If both Handrails have openings, at-
tach either Handrail to either Upright.
3. With the help of a second person, hold the Console Base
(8) and the other Handrail (51) near the right Upright (1).
It may be helpful to rest the left side of the Console Base
on the left Handrail (51).
Insert the Console Wire Harness (55) through the two in-
dicated openings in the right Handrail (51). Next, connect
the Console Wire Harness to the two plugs on the Wire
Harness (19). Refer to the inset drawing. Locate the two
Wire Ties (98) on the Console Wire Harness (55) and the
Wire Harness (19). Slide the Wire Ties against the plugs
as shown. Insert the 12Ó Wire Tie (99) through the holes
in the Wire Ties. Close and tighten the 12Ó Wire Tie.
51
19
8
55
50
95
95
97
97
1
51
Deck
50
82
50
1
2
3
95
19
98
98
99
55
51
1
a
