background image

5

Inductive Sensors

 CAUTION!

This signal word indicates a hazard with a low degree of risk which, if not avoided,  
may result in minor or moderate injury.

 ATTENTION!

This word draws attention to a potentially hazardous situation which, if not avoided, may 
result in property damage.

 NOTE!

A note draws attention to useful tips and suggestions, as well as information regarding 
efficient, error-free use.

1.3  Limitation of Liability

• The product has been developed in consideration of the current state-of-the-art technology, as well as 

applicable standards and guidelines. Subject to change without notice. A valid declaration of conformity 
can be found at www.wenglor.com in the product’s separate download area.

• wenglor sensoric elektronische Geräte GmbH (hereinafter referred to as "wenglor") excludes all liability in 

the event of:

• Non-compliance with the instructions
• Use of the product for purposes other than those intended
• Use by untrained personnel
• Use of unapproved replacement parts
• Unapproved modification of products

• These operating instructions do not include any guarantees from wenglor with regard to the described 

procedures or specific product characteristics.

• wenglor assumes no liability for printing errors or other inaccuracies contained in these operating instruc-

tions unless wenglor was verifiably aware of such errors at the point in time at which the operating instruc-
tions were prepared.

1.4  Copyrights

• The contents of these instructions are protected by copyright law.
• All rights are reserved by wenglor.
• Commercial reproduction or any other commercial use of the provided content and information, in particu-

lar graphics and images, is not permitted without previous written consent from wenglor.

Содержание I03H Series


















Отзывы: